Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.
That, however, was thwarted by the fix for [1]:
commit 9292f37e1f
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Thu Jan 5 09:34:28 2012 -0200
drm: give up on edid retries when i2c bus is not responding
This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).
Since its introduction in
commit f899fc64cd
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jul 20 15:44:45 2010 -0700
drm/i915: use GMBUS to manage i2c links
we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.
Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.
This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.
[1] https://bugs.freedesktop.org/show_bug.cgi?id=41059
v2: Don't retry if using bit banging.
v3: Move retry within gmbux_xfer, retry only on first message.
v4: Initialize GMBUS0 on retry (Ville).
v5: Take index reads into account (Ville).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924
Cc: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Tested-by: Oliver Grafe <oliver.grafe@ge.com> (v2)
Tested-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The encryption key size for LTKs is supposed to be applied only at the
moment of encryption. When generating a Link Key (using LE SC) from
the LTK the full non-shortened value should be used. This patch
modifies the code to always keep the full value around and only apply
the key size when passing the value to HCI.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the information exported by the IOMMU drivers to create
direct mapped regions in the default domains.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add two new functions to the IOMMU-API to allow the IOMMU
drivers to export the requirements for direct mapped regions
per device.
This is useful for exporting the information in Intel VT-d's
RMRR entries or AMD-Vi's unity mappings.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make use of the default domain and re-attach a device to it
when it is detached from another domain. Also enforce that a
device has to be in the default domain before it can be
attached to a different domain.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch changes the behavior of the iommu_attach_device
and iommu_detach_device functions. With this change these
functions only work on devices that have their own group.
For all other devices the iommu_group_attach/detach
functions must be used.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The default domain will be used (if supported by the iommu
driver) when the devices in the iommu group are not attached
to any other domain.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch implements fallocate's FALLOC_FL_INSERT_RANGE for Ext4.
1) Make sure that both offset and len are block size aligned.
2) Update the i_size of inode by len bytes.
3) Compute the file's logical block number against offset. If the computed
block number is not the starting block of the extent, split the extent
such that the block number is the starting block of the extent.
4) Shift all the extents which are lying between [offset, last allocated extent]
towards right by len bytes. This step will make a hole of len bytes
at offset.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
iser connection termination process happens in 2 stages:
- isert_wait_conn:
- resumes rdma disconnect
- wait for session commands
- wait for flush completions (post a marked wr to signal we are done)
- wait for logout completion
- queue work for connection cleanup (depends on disconnected/timewait
events)
- isert_free_conn
- last reference put on the connection
In case we are terminating during IOs, we might be posting send/recv
requests after we posted the last work request which might lead
to a use-after-free condition in isert_handle_wc.
After we posted the last wr in isert_wait_conn we are guaranteed that
no successful completions will follow (meaning no new work request posts
may happen) but other flush errors might still come. So before we
put the last reference on the connection, we repeat the process of
posting a marked work request (isert_wait4flush) in order to make sure all
pending completions were flushed.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When receiving a new iser connect request we serialize
the pending requests by adding the newly created iser connection
to the np accept list and let the login thread process the connect
request one by one (np_accept_wait).
In case we received a disconnect request before the iser_conn
has begun processing (still linked in np_accept_list) we should
detach it from the list and clean it up and not have the login
thread process a stale connection. We do it only when the connection
state is not already terminating (initiator driven disconnect) as
this might lead us to access np_accept_mutex after the np was released
in live shutdown scenarios.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit "2426bd456a target: Report correct response ..."
we might get a command with data_size that does not fit to
the number of allocated data sg elements. Given that we rely on
cmd t_data_nents which might be different than the data_size,
we sometimes receive local length error completion. The correct
approach would be to take the command data_size into account when
constructing the ib sg_list.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The new regmap code seems to cache this, which isn't helpful
for the hotplug dock situation where this gets updated.
Use the uncached query for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The MW regbase and vbase(s) were not being freed if an error occurred
in the vbase allocation loop. This is corrected by updating the error
path for the allocation loop to err4.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Need to adjust the number of CUs and RBs.
v2: get proper values
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver makes use of this information so print if to aid in
debugging.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the unnecessary returned status and make the IOCTL write only.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
We need to reset the bo_va address, otherwise new mappings
wouldn't be updated in the page table.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Pull networking fixes from David Miller:
1) Fix stack allocation in s390 BPF JIT, from Michael Holzheu.
2) Disable LRO on openvswitch paths, from Jiri Benc.
3) UDP early demux doesn't handle multicast group membership properly,
fix from Shawn Bohrer.
4) Fix TX queue hang due to incorrect handling of mixed sized fragments
and linearlization in i40e driver, from Anjali Singhai Jain.
5) Cannot use disable_irq() in timer handler of AMD xgbe driver, from
Thomas Lendacky.
6) b2net driver improperly assumes pci_alloc_consistent() gives zero'd
out memory, use dma_zalloc_coherent(). From Sriharsha Basavapatna.
7) Fix use-after-free in MPLS and ipv6, from Robert Shearman.
8) Missing neif_napi_del() calls in cleanup paths of b44 driver, from
Hauke Mehrtens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: replace last open coded skb_orphan_frags with function call
net: bcmgenet: power on MII block for all MII modes
ipv6: Fix protocol resubmission
ipv6: fix possible use after free of dev stats
b44: call netif_napi_del()
bridge: disable softirqs around br_fdb_update to avoid lockup
Revert "bridge: use _bh spinlock variant for br_fdb_update to avoid lockup"
mpls: fix possible use after free of device
be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()
bridge: use _bh spinlock variant for br_fdb_update to avoid lockup
amd-xgbe: Use disable_irq_nosync from within timer function
rhashtable: add missing import <linux/export.h>
i40e: Make sure to be in VEB mode if SRIOV is enabled at probe
i40e: start up in VEPA mode by default
i40e/i40evf: Fix mixed size frags and linearization
ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()
openvswitch: disable LRO
s390/bpf: fix bpf frame pointer setup
s390/bpf: fix stack allocation
Previously the elan_i2c touchpad driver would simply request the firmware
"/lib/firmware/elan_i2c.bin", which does not work well if there are
multiple such devices in the system.
Let's append the "product ID" (by using the same function as the sysfs
interface for consistency) to the filename. This results in filenames of
the form "/lib/firmware/elan_i2c_72.0.bin", allowing you to support
multiple elan_i2c touchpads on the same device by simply naming each
device's FW with its corresponding product ID. This way when you trigger a
fw update the driver will load the correct binary.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple IC types for i2c/smbus protocol, add get ic
type command and use this data when checking firmware page count and
signature address.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes a minor issue affecting multiqueue virtio net
when user keeps changing the number of active queues
and CPUs are added and removed by hotplug.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVdgTnAAoJECgfDbjSjVRpP0IIAKfJaaxXKJEzHQ8k/8w8MNI3
xqyDV53kvWWHgwLTw1IxrLs0J2hkwdCnEnuRbwEm5XT9n2MoZDh3hC5A9gDN9NkW
rGDL2zX63gsdNyv5cxeXHWPLaph1NAL1Ausf0SEwLm7mTPbd6wJETITpdlV3dhLF
00NrlrF+0O3SlWHX7eVHWC1sI4Uc7BNXMuj4TZ0xv64xbuoTCsJeaij2t/ptqpwS
ao8trxbL3OcAY7wxeVsDz6sjkKE4+qlpgfXC8nw8+waFPrH3xfylo123qyeRWm3b
qqLxmCq2J0s3LUBCgvn4lKJdHGZEKtrUGbQ+qhYBrvCcMC+sOrbOv9kS3JwTC+E=
=zOjK
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull last-minute virtio fix from Michael Tsirkin:
"This fixes a minor issue affecting multiqueue virtio net when user
keeps changing the number of active queues and CPUs are added and
removed by hotplug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: Clear stale cpumask when setting irq affinity
Vendor commands are passed from userspace through the
NFC_CMD_VENDOR netlink command, allowing driver and hardware
specific operations implementations like for example RF tuning
or production line calibration.
Drivers will associate a set of vendor commands to a vendor
id, which could typically be an OUI. The netlink kernel
implementation will try to match the received vendor id
and sub command attributes with the registered ones. When
such match is found, the driver defined sub command routine
is called.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Together with inline routines to associate a vendor commands
array with an NFC device.
Vendor commands allow vendors to implement their very specific
operations from driver code instead of adding new stack ops
for non NFC generic commands.
Vendors need to select their own unique IDs and use that as a
namespace for defining sub commands.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A week late but I managed to complete it all and moved it into Git, for better
structure and easy pulling.
Changes relative to the last submission:
- Added higher level subsystem directories to collect features by
subsystem:
triton:~/tip> ls Documentation/features/
arch-support.txt core debug io lib list-arch.sh locking perf sched seccomp time vm
each subsystem directory contains the feature directories. For example locking
has:
triton:~/tip> ls Documentation/features/locking/
cmpxchg-local lockdep queued-rwlocks queued-spinlocks rwsem-optimized
It's all pretty straightforward to navigate. Advantages are better
visualization, plus git log is able to list changes per subsystem.
- Prettified the visualization some more.
- Improved/corrected the support matrices based on feedback to earlier submissions.
- Updated the support matrices to today's linux-next, so that by the time this
shows up in upstream in the next merge window it's really recent.
Most notably there's a new architecture in linux-next (h8300).
This structure should address all feedback that I got and should minimize the
maintenance overhead (chance of conflicts).
Updated struct file_operations documentation in vfs.txt to match
current implementation
Signed-off-by: Thomas de Beauchene <chauvo_t@epitech.eu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/atm/iphase.c:2621:4-20:
WARNING: timeout (50) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which does not seem intended.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
As this driver was introduced in the early 2.3 series it is most
likely assuming HZ=100 so the constant 50 is converted to 500ms.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 976591810f (kbuild Update documentation of clean-files and clean-dirs)
changed the example for the clean-files variable, but left the explanation
unchanged. Edit the explanation to match the example.
Signed-off-by: Jeffrey Rogers <jeffreydavidrogers@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Various boot loaders for Exynos based boards use certain memory
addresses during booting for different purposes. Mostly this is one of
following :
1. as a CPU boot address,
2. for storing magic cookie related to low power mode (AFTR, sleep).
The document, based solely on kernel source code, tries to group the
information scattered over different files. This would help in the
future when adding support for new SoC or when extending features
related to low power modes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In order to prevent any NFC feature when NFC is disable and
to save power, (down to 4uA) put the CLF in hibernate mode
with RF deactivated.
Add the equivalent to enable the NFC feature when initiating
the st21nfcb driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st21nfcb is disabled, the irq line may remain active
while no data are available, flooding the system with
irrelevant i2c transaction.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The powered flag can be set from the ndlc_open and ndlc_close layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Removing st21nfcb may need to execute some specific commands before
stopping the ndlc state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On st21nfcb, nci proprietary commands are available to run
specific chip operations (for example: power management)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing st21nfcb driver, flag ST21NFCB_NCI_RUNNING can be cleared
only once the ndlc and the transport (i2c or spi) layers are released.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to release the st21nfcb properly close the ndlc
layer first.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ndlc_remove already calls st21nfcb_nci_i2c_disable and
phy->powered is already set to 0.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Once the data is sent, we need to preserve the full frame for
the ndlc state machine. If the NDLC ACK is not received in time,
the ndlc layer will resend the same frame.
Having the header byte pulled will corrupt the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since ndev->driver_data is allocated by devm_kzalloc(), we do not
need the inappropriate kfree to free it in driver's remove function.
Freeing will trigger when driver unloads.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
