The width and height needs to be swapped
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[rebased on top of v4.18-rc1]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
On some Mali-DP processors, the LAYER_FORMAT register contains fields
other than the format. These bits were unconditionally cleared when
setting the pixel format, whereas they should be preserved at their
reset values.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
This patch fixes the below parser error of the IOB SLOW PMU.
# perf stat -a -e iob-slow0/cycle-count/ sleep 1
evenf syntax error: 'iob-slow0/cycle-count/'
\___ parser error
It replaces the "-" character by "_" character inside the PMU name.
Signed-off-by: Hoan Tran <hoan.tran@amperecomputing.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a9 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should be using IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb94120 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029f ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should use IRQ_TYPE_LEVEL_HIGH instead of
IRQ_TYPE_NONE.
Fixes: 0f9f27a36d ("ARM: dts: NSP: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the MAINTAINERS file to cover the "stingray" pattern and a few
files under arch/arm64/boot/dts/broadcom/* as well as the clock driver
and binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While moving the Northstar 2 DTS into a dedicated directory, the
corresponding MAINTAINERS file entry was not updated accordingly, fix
that.
Fixes: 63a913c157 ("arm64: dts: move ns2 into northstar2 directory")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Delete RUN_TESTS and EMIT_TESTS overrides and use common defines in
lib.mk. Common defines work just fine and there is no need to define
custom overrides.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Tom Hromatka <tom.hromatka@oracle.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
sparc64 test fails with the following errors on non-sparc64 systems. Fix
the Makefile to do nothing on non-sparc64 systems to suppress the errors:
make run_tests
adi-test.c: Assembler messages:
adi-test.c:302: Error: no such instruction: `rd %tick,%r13'
adi-test.c:304: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:190: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:192: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:273: Error: no such instruction: `rd %tick,%rbx'
adi-test.c:276: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:217: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:220: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:246: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:248: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
<builtin>: recipe for target 'adi-test' failed
make[1]: *** [adi-test] Error 1
adi: [FAIL]
./drivers_test.sh: 24: ./drivers_test.sh: ./adi-test: not found
../lib.mk:73: recipe for target 'run_tests' failed
make: *** [run_tests] Error 1
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Tom Hromatka <tom.hromatka@oracle.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Unless the software synchronization objects (CONFIG_SW_SYNC) is enabled,
the sync test will be skipped:
TAP version 13
1..0 # Skipped: Sync framework not supported by kernel
Add a config fragment file to be able to run "make kselftest-merge" to
enable relevant configuration required in order to run the sync test.
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Link: https://lkml.org/lkml/2017/5/5/14
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When vm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the
test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When zram test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When user test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run. Add an explicit check
for module presence and return skip code if module isn't present.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When sysctl test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Changed return code to kselftest skip code in skip error legs that check
requirements and module probe test error leg.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When static_keys test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as a fail
by the Kselftest framework. This leads to false negative result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit searches for test_static_key_base and test_static_keys
modules and return skip code if they aren't found to differentiate between
the failure to load the module condition and module not found condition.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When pstore_post_reboot test gets skipped because of unmet dependencies
and/or unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
On this system EC interrupt triggers constantly kicking devices out of
low power states and thus blocking power management. The system also has
a PCIe root port hosting Alpine Ridge Thunderbolt controller and it
never gets a chance to go to D3cold because of this.
Since the power button works the same regardless if EC interrupt is
enabled or not during s2idle, add a quirk for this machine that sets
ec_no_wakeup=true preventing spurious wakeups.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 2c17a4368a.
The offending commit triggers a run-time fault when accessing the panel
element of the sun4i_tcon structure when no such panel is attached.
It was apparently assumed in said commit that a panel is always used with
the TCON. Although it is often the case, this is not always true.
For instance a bridge might be used instead of a panel.
This issue was discovered using an A13-OLinuXino, that uses the TCON
in RGB mode for a simple DAC-based VGA bridge.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613081647.31183-1-paul.kocialkowski@bootlin.com
With gcc 4.1.2:
drivers/pinctrl/actions/pinctrl-owl.c: In function ‘owl_pin_config_set’:
drivers/pinctrl/actions/pinctrl-owl.c:336: warning: ‘ret’ may be used uninitialized in this function
Indeed, if num_configs is zero, the uninitialized value will be returned
as an error code.
Fix this by preinitializing it to zero.
Fixes: 2242ddfbf4 ("pinctrl: actions: Add Actions S900 pinctrl driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently saved_vals is being allocated and there is no check for
failed allocation (which is more likely than normal when using
GFP_ATOMIC). Fix this by checking for a failed allocation and
propagating this error return down the the caller chain.
Detected by CoverityScan, CID#1469841 ("Dereference null return value")
Fixes: 88a1dbdec6 ("pinctrl: pinctrl-single: Add functions to save and restore pinctrl context")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit b89405b610 ("pinctrl: devicetree: Fix dt_to_map_one_config
handling of hogs") causes the pinctrl hog pins to not get initialized
on i.MX platforms leaving them with the IOMUX settings untouched.
This causes several regressions on i.MX such as:
- OV5640 camera driver can not be probed anymore on imx6qdl-sabresd
because the camera clock pin is in a pinctrl_hog group and since
its pinctrl initialization is skipped, the camera clock is kept
in GPIO functionality instead of CLK_CKO function.
- Audio stopped working on imx6qdl-wandboard and imx53-qsb for
the same reason.
Richard Fitzgerald explains the problem:
"I see the bug. If the hog node isn't a 1st level child of the pinctrl
parent node it will go around the for(;;) loop again but on the first
pass I overwrite pctldev with the result of
get_pinctrl_dev_from_of_node() so it doesn't point to the pinctrl driver
any more."
Fix the issue by stashing the original pctldev so it doesn't
get overwritten.
Fixes: b89405b610 ("pinctrl: devicetree: Fix dt_to_map_one_config handling of hogs")
Cc: <stable@vger.kernel.org>
Reported-by: Mika Penttilä <mika.penttila@nextfour.com>
Reported-by: Steve Longerbeam <slongerbeam@gmail.com>
Suggested-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=KTNX
-----END PGP SIGNATURE-----
Merge tag '4.18-rc1-more-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Misc SMB3 fixes, including particularly important ones for signing,
some minor documentation and debug improvements and another posix
smb3.11 fix"
* tag '4.18-rc1-more-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix invalid check in __cifs_calc_signature()
cifs: Use correct packet length in SMB2_TRANSFORM header
smb3: fix corrupt path in subdirs on smb311 with posix
smb3: do not display empty interface list
smb3: Fix mode on mkdir on smb311 mounts
cifs: Fix kernel oops when traceSMB is enabled
CIFS: dump every session iface info
CIFS: parse and store info on iface queries
CIFS: add iface info to struct cifs_ses
CIFS: complete PDU definitions for interface queries
CIFS: move default port definitions to cifsglob.h
cifs: Fix encryption/signing
cifs: update __smb_send_rqst() to take an array of requests
cifs: remove smb2_send_recv()
cifs: push rfc1002 generation down the stack
smb3: increase initial number of credits requested to allow write
cifs: minor documentation updates
cifs: add lease tracking to the cached root fid
smb3: note that smb3.11 posix extensions mount option is experimental
Pull dmi update from Jean Delvare:
"Expose SKU ID string as a DMI attribute"
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi: Add access to the SKU ID string
This fixes this documentation build error that is due to a file rename:
Error: Cannot open file ../arch/x86/kernel/cpu/mtrr/main.c
Fixes: 0afe832e55 ("Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is used in some systems from user space for determining the identity
of the device.
Expose this as a file so that that user-space tools don't need to read
from /sys/firmware/dmi/tables/DMI
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The statement always evaluates to true since the struct fields
are arrays. This has shown up as a warning when compiling with
clang:
warning: address of array 'desc->layout.xstride' will always
evaluate to 'true' [-Wpointer-bool-conversion]
Check for values in the first plane instead.
Fixes: 1a396789f6 ("drm: add Atmel HLCDC Display Controller support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180617084826.31885-1-stefan@agner.ch
Correct MIPI/PCIe/USB_HSIC's PGC offset based on
design RTL, the values in the Reference Manual
(Rev. 1, 01/2018 and the older ones) are incorrect.
The correct offset values should be as below:
0x800 ~ 0x83F: PGC for core0 of A7 platform;
0x840 ~ 0x87F: PGC for core1 of A7 platform;
0x880 ~ 0x8BF: PGC for SCU of A7 platform;
0xA00 ~ 0xA3F: PGC for fastmix/megamix;
0xC00 ~ 0xC3F: PGC for MIPI PHY;
0xC40 ~ 0xC7F: PGC for PCIe_PHY;
0xC80 ~ 0xCBF: PGC for USB OTG1 PHY;
0xCC0 ~ 0xCFF: PGC for USB OTG2 PHY;
0xD00 ~ 0xD3F: PGC for USB HSIC PHY;
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 03aa12629f ("soc: imx: Add GPCv2 power gating driver")
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The commentary says to use various parameters, and lays out what
the mapping is... The code used a 32KHz rate when the comment
says that it needs to use a 48KHz rate. And this has been the
case since day one.
On the Alienware M17x R4, the DMic used to have exceptionally quiet
pickup and a lot of noise. Changing the data rate fixes both of
these issues.
Searching the kernel bug tracker for ca0132-related issues shows no
mention of this being an issue for other hardware, and I have no
other hardware to test with, so a quirk is used to limit the effect
to just the M17x R4.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 009b8f979b conditionalized
adding the "CA0132 Analog Mic-In2" PCM with a comment to the
effect that, "desktops don't use this ADC", but the test was set
up such that the ADC was only created for desktops. Invert the
test.
Fixes: 009b8f979b ("ALSA: hda/ca0132: update core functions for sbz + r3di")
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
QUIRK_NONE is, quite explicitly, the default case. The entire
point of a quirks system is to allow "programming by difference"
from a given base case, which requires that merely defining a new
quirk for some piece of hardware should not change the behavior of
the driver for that hardware. In turn, this means that testing
for QUIRK_NONE explicitly is a violation of that implicit contract.
Change a test for QUIRK_NONE and QUIRK_ALIENWARE to default, and
add a test for QUIRK_SBZ to disable the default behavior in that
instance.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit e93ac30a32 (ALSA: HDA/ca0132:
add extra init functions for r3di + sbz) introduced an extra
initialization function that was improperly guarded, taking effect
on systems with QUIRK_ALIENWARE, even though such systems were
supposedly not affected.
It may be that this piece of initialization should be done for all
systems, but that's not a call that I can make.
Fixes: e93ac30a32 ("ALSA: HDA/ca0132: add extra init functions for r3di + sbz")
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During ca0132_init(), ca0132_init_unsol() is run before the
spec->spec_init_verbs are written. ca0132_init_unsol() calls
snd_hda_jack_detect_enable_callback(), which requests UNSOL events
for three or four nodes, two of which were also (redundantly)
requested by spec_init_verbs.
Kill the redundant AC_VERB_SET_UNSOLICITED_ENABLE verbs.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ca0132_config() was setting some values in the auto_pin_cfg for
the codec... but it is called prior to snd_hda_parse_pin_defcfg(),
which does a memset() to clear the entire structure as one of its
first actions, making the entire exercise pointless.
Kill all use of struct auto_pin_cfg from ca0132_config().
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Lenovo laptops, e.g. Lenovo P50, showed the pop noise at resume
or runtime resume. It turned out to be reduced by applying
alc_no_shutup() just like TPT440 quirk does.
Since there are many Lenovo models showing the same behavior, put this
workaround in ALC269_FIXUP_THINKPAD_ACPI entry so that it's applied
commonly to all such Lenovo machines.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Berg <bberg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
commit dd4b487b32 ("ARM: dts: imx6: Use correct SDMA script
for SPI cores") is fixing the same issue but only for SPI1 - 4.
Fixes: 677940258d ("ARM: dts: imx6q: enable dma for ecspi5")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When blackhole is used on top of classful qdisc like hfsc it breaks
qlen and backlog counters because packets are disappear without notice.
In HFSC non-zero qlen while all classes are inactive triggers warning:
WARNING: ... at net/sched/sch_hfsc.c:1393 hfsc_dequeue+0xba4/0xe90 [sch_hfsc]
and schedules watchdog work endlessly.
This patch return __NET_XMIT_BYPASS in addition to NET_XMIT_SUCCESS,
this flag tells upper layer: this packet is gone and isn't queued.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
