For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before 5b83b2234b the driver was hard coding the wakeup irq to
be active low. The generic pm wakeirq does not override the active
high/low parameter, hence it must be specified correctly in the
device tree.
Mind that SDIO IRQ is active low as defined in the SDIO specification
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's excessive to use prefix for the parameters when you do
modprobe mmc-block mmcblk.perdev_minors=16
Make this available only for built-in case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch over pxamci to dmaengine. This prepares the devicetree full
support of pxamci.
This was successfully tested on a PXA3xx board, as well as PXA27x.
Signed-off-by: Daniel Mack <zonque@gmail.com>
[adapted to pxa-dma]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Inline function __dma_request_slave_channel_compat() doesn't modify "name"
argument but passes it to dma_request_slave_channel() which already takes
it as a constant.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Don't use the direction passed in the configuration, and rely on each
transfer's direction to prepare the transfers. This will enable
future removal of direction parameter from dma_slave_config.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This adds new descriptor flag for reusing a descriptor by submitting
multiple times by a client, for example video buffer.
Add helper APIs for this as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by:Robert Jarzmik <robert.jarzmik@free.fr>
As reported by Alexey Khoroshilov:
grgpio_irq_unmap() code looks quite suspicious regarding usage of
priv->bgc.lock spinlock.
It locks the spinlock in line 310:
spin_lock_irqsave(&priv->bgc.lock, flags);
and then it can call grgpio_set_imask() in line 317:
grgpio_set_imask(priv, i, 0);
But grgpio_set_imask() unconditionally locks the spinlock by itself.
Fix this by moving the spinlock acquisition outside of
grgpio_set_imask().
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compare pointer-typed values to NULL rather than 0.
The semantic patch that makes this change is available
in scripts/coccinelle/null/badzero.cocci
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that the AEAD conversion is complete we can rip out the old
AEAD interafce and associated code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The qat driver uses crypto_aead_crt in order to get the authsize.
This patch replaces it with the crypto_aead_authsize helper instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pretty soon the crypto_aead encrypt/decrypt hooks will disappear
as they are now always identical to those in struct aead_alg.
This patch replaces the references to these hooks with the ones
from aead_alg instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the helpers aead_init_geniv and aead_exit_geniv
which are type-safe and intended the replace the existing geniv
init/exit helpers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that we no longer have any legacy AEAD implementations the
compatibility code path can no longer be triggered. This patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that we no longer have any legacy AEAD implementations the
compatibility code path can no longer be triggered. This patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that seqniv is identical with seqiv we no longer need it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
As IV generators are now standalone AEAD transforms, we no longer
need to use the crypto_lookup_aead call.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When NFC_ATTR_VENDOR_DATA is not set, data_len is 0 and data is NULL.
Fixes the following warning:
net/nfc/netlink.c:1536:3: warning: 'data' may be used uninitialized
+in this function [-Wmaybe-uninitialized]
return cmd->doit(dev, data, data_len);
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Both the per-APIC flag ".wait_for_init_deassert",
and the global atomic_t "init_deasserted"
are dead code -- remove them.
For all APIC types, "wait_for_master()"
prevents an AP from proceeding until the BSP has set
cpu_callout_mask, making "init_deasserted" {unnecessary}:
BSP: <de-assert INIT>
...
BSP: {set init_deasserted}
AP: wait_for_master()
set cpu_initialized_mask
wait for cpu_callout_mask
BSP: test cpu_initialized_mask
BSP: set cpu_callout_mask
AP: test cpu_callout_mask
AP: {wait for init_deasserted}
...
AP: <touch APIC>
Deleting the {dead code} above is necessary to enable
some parallelism in a future patch.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/de4b3a9bab894735e285870b5296da25ee6a8a5a.1439739165.git.len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
MPS 1.4 example code shows the following required delays during processor
on-lining:
INIT
udelay(10,000)
SIPI
udelay(200)
SIPI
udelay(200) /* Linux actually implements this as udelay(300) */
Linux skips the udelay(10,000) on modern processors.
This patch removes the udelay(200) after each SIPI
on those same processors.
All three legacy delays can be restored by the cmdline
"cpu_init_udelay=10000".
As measured by analyze_suspend.py, this patch speeds
processor resume time on my desktop from 2.4ms to 1.8ms, per AP.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/a5dfdbc8fbfdd813784da204aad5677fe459ac37.1439739165.git.len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After the BSP sends INIT/SIPI/SIP to the AP and sees the AP
in the cpu_initialized_map, it sets the AP loose via the
cpu_callout_map, and waits for it via the cpu_callin_map.
The BSP polls the cpu_callin_map with a udelay(100)
and a schedule() in each iteration.
The udelay(100) adds no value.
For example, on my 4-CPU dekstop, the AP finishes
cpu_callin() in under 70 usec and sets the cpu_callin_mask.
The BSP, however, doesn't see that setting until over 30 usec
later, because it was still running its udelay(100)
when the AP finished.
Deleting the udelay(100) in the cpu_callin_mask polling loop,
saves from 0 to 100 usec per Application Processor.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/0aade12eabeb89a688c929fe80856eaea0544bb7.1439739165.git.len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After the BSP sends the APIC INIT/SIPI/SIPI to the AP,
it waits for the AP to come up and indicate that it is alive
by setting its own bit in the cpu_initialized_mask.
Linux polls for up to 10 seconds for this to happen.
Each polling loop has a udelay(100) and a call to schedule().
The udelay(100) adds no value.
For example, on my desktop, the BSP waits for the
other 3 CPUs to come on line at boot for 305, 404, 405 usec.
For resume from S3, it waits 317, 404, 405 usec.
But when the udelay(100) is removed, the BSP waits
305, 310, 306 for boot, and 305, 307, 306 for resume.
So for both boot and resume, removing the udelay(100)
speeds online by about 100us in 2 of 3 cases.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/33ef746c67d2489cad0a9b1958cf71167232ff2b.1439739165.git.len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I've been searching for any documentation of 'the active-low property of a GPIO'
already mentioned in this documenation. But couldn't find any. Add it.
Sigend-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
[Spelling, grammar fixes]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We forgot to install the tempfile, so when the selftests are installed
and then run the subpage_prot_file test fails.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
wil6210:
* implement TSO support
* support bootloader v1 and onwards
As discussed recently the meaning of DMA_CTRL_ACK is that a desc cannot be
reused by provider until the client acknowledges receipt, i.e. has has a
chance to establish any dependency chains. So update documentation
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by:Robert Jarzmik <robert.jarzmik@free.fr>
IOAT_COMPLETION_PENDING flag was deprecated for v2 and v3 drivers but was
not cleaned up. Doing that now. The commit deprecated this flag was
4dec23d7 ioatdma: fix race between updating ioat->head and
IOAT_COMPLETION_PENDING.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
./scripts/kerne-doc is reporting errors on dma.h. Clean up all reported
errors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we are a "single" device driver now we no longer require the function
pointers in ioatdma_device. Remove.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving the relevant functions to their respective .c files and removal of
dma_v3.c file. Also removed various ioat3 references when appropriate.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move all DMA descriptor prepping functions to prep.c file. Fixup all
broken bits caused by the move.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving all the init routines to init.c and fixup anything broken during
the move.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move and fixup all sysfs related bits to sysfs.c file.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
