Change loops in ac97_read/write functions to count down to zero
rather than up. Gcc will then use the 'dt' (decrement-and-test) op
instead of an increment/compare op-pair.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added initial support for the STAC92HD71BXX family of codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The Audio interface on HD2400/HD2600 cards isn't currently detected by
snd-hda-intel. I added missing pci device ids for RV610 and RV630, but
I only had a HD2400 pro card to test, where now the audio interface is
detected (and no need to change patch_atihdmi.c, as the codec vendor id
remains 0x1002aa01 for which we already have an entry there). I also
couldn't test if sound pass-trough is ok (and I don't know how to), but
at least now the device is detected.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
We have to do fairly accurate counting of the minimal periods, instead
of being lazy and just setting the number to zero as soon as one period
elapses.
Signed-off-by: Joachim Foerster <JOFT@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add ALSA support for the opb_ac97_controller_ref_v1_00_a ip core found
in Xilinx' ML403 reference design.
Known issue: Currently this driver hits a WARN_ON_ONCE(1) statement in
kernel/irq/resend.c (line 70). According to Linus
(http://lkml.org/lkml/2007/8/5/5) this may be ignored, right? I haven't
had a look into this 'problem' yet.
Signed-off-by: Joachim Foerster <JOFT@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for the dmics and enabled EAPD for several laptops with
STAC9228 cards.
Signed-off-by: Matthew Ranostay <mranostay@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simple patch to add the Asus VX1 laptop to the Analog Devices pci quirk list.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for 88.2k, 96k, and 128k samplerates
on cmi8738-55 chip.
Analog playback works fine on all channels.
Analog capture works well too, though the extra samples seems
interpolated by hardware.
spdif playback and capture works fine.
Signed-off-by: Timofei Bondarenko <tim@ipi.ac.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some small improvements on autocfg stuff:
- sort HP pins by sequence number, too
- move sole mic pin to AUTO_PIN_MIC instead of AUTO_PIN_FRONT_MIC
- ditto for line-in pin
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch improves support for 'SB Live 24-bit Extarnal' USB card.
1) This card can go into muted state when a headphones connected or
disconnected. So notify mixer about changes in headphone jack.
2) Add LED controls and procfs support just as in similar Audigy 2 NX card.
3) Rename 'PCM Capture' conrol to 'Mic Capture' to reflect reality:
the card may adjust microphone input level only.
Signed-off-by: Timofei Bondarenko <tim@ipi.ac.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove sequencer instrument layer from the tree.
This mechanism hasn't been used much with the actual devices. The only
reasonable user was OPL3 loader, and now it was rewritten to use hwdep
instead. So, let's remove the rest of rotten codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the exclusive access lock in hwdep instead of the own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the hwdep device for loading OPL2/3 patch data instead of the
messy sequencer instrument layer.
Due to this change, the sbiload program should be updated, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch supresses an annoying compiler warning that the variable
err may be used uninitialised.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch kills these two compilation warnings if
power management is disabled:
sound/pci/ac97/ac97_patch.h:86: warning: 'snd_ac97_restore_status'
declared 'static' but never defined
sound/pci/ac97/ac97_patch.h:87: warning: 'snd_ac97_restore_iec958'
declared 'static' but never defined
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Introduced the global 'slots' option to snd module. This option provides
an alternative way to handle the order of multiple sound card instances.
It's an easier approach to avoid conflict with hotplug devices, and can
be used together with the existing 'order' option of each card driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Show the current EAPD status and volume-knob status in proc file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds ac97 support for ln2440sbc board from LittleChips.
This board is based on s3c2440 SoC + AC97 Realtek ALC650 codec.
Existing s3c2443 implementation is slightly modified because s3c2440
and s3c2443 have different AC97 interrupts.
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds full record and playback support for the Samsung Q1
Ultra - Vista model (different codec than the earlier Q1 Ultra models).
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix quirk for Shuttle AK32VN. It works better with DXS_SRC, and needs
HP_ONLY ac97 quirk.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the print format for debug message.
Spotted by Matthew Wilcox.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch brings some English style improvements throughout the
document, as well as 1 or 2 extra technical details.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Onkyo SE-90PCI and SE-200PCI boards.
Signed-off-by: Shin-ya Okada <sh_okada at d4.dion.ne.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The following patch adds 'Mono Playback Switch' control to WM9712 codec
SoC driver.
Also, it fixes Treble, Bass and Mono playback volume inversion bits.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Changed the dmux for STAC9228 from ADC1MUX to ADC0MUX to avoid confusion.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a dmux to the STAC9228 cards with DMIC support. And added a
STAC_DIGITAL_INPUT_SOURCE macro for repeating mixer code.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing STAC9228 DMIC support.
Also added a new vendor id tag for IDT.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing model string 'eeepc-p701' for ALC662 codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
drivers/lguest/x86/core.c: In function ‘copy_in_guest_info’:
drivers/lguest/x86/core.c:97: error: ‘struct x86_hw_tss’ has no member named ‘esp1’
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More late-caught fallout from the mainline merge. Commit
35e4a6e26d ("[POWERPC] Use
archdata.dma_data in dma_direct_ops and add the offset") claimed
"Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, ..."
..but nope -- the pasemi iommu setup code that disables translation on
the DMA pci device didn't set dma_data correctly.
This fixes it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, only one debounce_interval is introduced for both direct and
matrix keys. This is true in most cases, although the keypad controller
supports different debounce for direct/matrix keys.
Some platforms do require this to be tuned, instead of the default
reset value of 100ms.
Rotary encoder will always use zero debounce time for now to achieve
certain sensitivity.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. use ioremap() for registers access, this improves the portability
of the driver (e.g. same IP on different processor with different
I/O memory range), and make it possible to remove those registers
definition in pxa-regs.h as PXA is undergoing a clean-up of that
header file
2. use device specific IRQ instead of hardcoded IRQ_KEYPAD, same
reason as above
3. clean up the error handling path in _probe()
4. remove DRIVER_NAME and use pdev->name when necessary, we don't
actually need a constant string literals
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Rotary encoder events can be configured either as relative events
as the legacy code does or as any specified key code, this is
useful on some platform which uses the rotary keys as
KEY_{UP/DOWN/LEFT/RIGHT}
2. Add support for direct keys, the corresponding keycodes for each
direct key can now be specified within the platform data
3. Remove the direct/rotary key detection code from the IRQ handler
to dedicated functions to improve readability
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduce pxa27x_keypad_config() for keypad registers configuration
and remove the reg_kpc, reg_kprec from platform data structure
so that configurations of keypad registers can be centralized to a
single function.
It can also be re-used when resuming.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Introduce the "struct pxa27x_keypad" structure for driver specific
information, such as "struct clk", generated matrix key codes and
so on
2. Use KEY() macro to define matrix keys, instead of original 8x8 map
this makes definition easier with keypad where keys are sparse
3. Keep a generated array in "struct pxa27x_keypad" for fast lookup
4. Separate the matrix scan into a dedicated function for readability
and report only those keys whose state has been changed, instead
of report all states
5. Make use of KPAS to decide the faster path if only one key has been
detected
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pin configurations will slowly be moved to the board specific code
at initialization thus to make the driver more generic.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The controller should really be called keypad, and also align
the naming of functions and structures to use "pxa27x_keypad"
as prefix, instead of "pxakbd".
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-2.6.25' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (454 commits)
[POWERPC] Cell IOMMU fixed mapping support
[POWERPC] Split out the ioid fetching/checking logic
[POWERPC] Add support to cell_iommu_setup_page_tables() for multiple windows
[POWERPC] Split out the IOMMU logic from cell_dma_dev_setup()
[POWERPC] Split cell_iommu_setup_hardware() into two parts
[POWERPC] Split out the logic that allocates struct iommus
[POWERPC] Allocate the hash table under 1G on cell
[POWERPC] Add set_dma_ops() to match get_dma_ops()
[POWERPC] 83xx: Clean up / convert mpc83xx board DTS files to v1 format.
[POWERPC] 85xx: Only invalidate TLB0 and TLB1
[POWERPC] 83xx: Fix typo in mpc837x compatible entries
[POWERPC] 85xx: convert sbc85* boards to use machine_device_initcall
[POWERPC] 83xx: rework platform Kconfig
[POWERPC] 85xx: rework platform Kconfig
[POWERPC] 86xx: Remove unused IRQ defines
[POWERPC] QE: Explicitly set address-cells and size cells for muram
[POWERPC] Convert StorCenter DTS file to /dts-v1/ format.
[POWERPC] 86xx: Convert all 86xx DTS files to /dts-v1/ format.
[PPC] Remove 85xx from arch/ppc
[PPC] Remove 83xx from arch/ppc
...
This patch adds support for setting up a fixed IOMMU mapping on certain
cell machines. For 64-bit devices this avoids the performance overhead of
mapping and unmapping pages at runtime. 32-bit devices are unable to use
the fixed mapping.
The fixed mapping is established at boot, and maps all of physical memory
1:1 into device space at some offset. On machines with < 30 GB of memory
we setup the fixed mapping immediately above the normal IOMMU window.
For example a machine with 4GB of memory would end up with the normal
IOMMU window from 0-2GB and the fixed mapping window from 2GB to 6GB. In
this case a 64-bit device wishing to DMA to 1GB would be told to DMA to
3GB, plus any offset required by firmware. The firmware offset is encoded
in the "dma-ranges" property.
On machines with 30GB or more of memory, we are unable to place the fixed
mapping above the normal IOMMU window as we would run out of address space.
Instead we move the normal IOMMU window to coincide with the hash page
table, this region does not need to be part of the fixed mapping as no
device should ever be DMA'ing to it. We then setup the fixed mapping
from 0 to 32GB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the ioid fetching and checking logic so we can use it elsewhere
in a subsequent patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to cell_iommu_setup_page_tables() for handling two windows,
the dynamic window and the fixed window. A fixed window size of 0
indicates that there is no fixed window at all.
Currently there are no callers who pass a non-zero fixed window, but the
upcoming fixed IOMMU mapping patch will change that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split the IOMMU logic out from cell_dma_dev_setup() into a separate
function. If we're not using dma_direct_ops or dma_iommu_ops we don't
know what the hell's going on, so BUG.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split cell_iommu_setup_hardware() into two parts. Split the page table
setup into cell_iommu_setup_page_tables() and the bits that kick the
hardware into cell_iommu_enable_hardware().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the logic that allocates a struct iommu into a separate
function. This can fail however the calling code has never cared - so
just return if we can't allocate an iommu.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to support the fixed IOMMU mapping (in a subsequent patch),
we need the hash table to be inside the IOMMUs DMA window. This is
usually 2G, but let's make sure the hash table is under 1G as that
will satisfy the IOMMU requirements and also means the hash table will
be on node 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
