The following GigaDevice chips have the QE BIT in the feature flags, I
checked the datasheets, but did not try this.
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
The Quad operations like 0xEB mention that the QE bit has to be set.
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-3-hauke@hauke-m.de
The datasheet only lists one dummy byte in the 0xEH operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-2-hauke@hauke-m.de
vf610_nfc_probe() does not invoke clk_disable_unprepare() on one error
handling path. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 6f0ce4dfc5 ("mtd: rawnand: vf610: Avoid a potential NULL pointer dereference")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200806072634.23528-1-novikov@ispras.ru
The Macronix MX31UF1GE4BC is a 1.8V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-3-git-send-email-ycllin@mxic.com.tw
The Macronix MX31LF1GE4BC is a 3V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-2-git-send-email-ycllin@mxic.com.tw
The sparse tool complains as follows:
drivers/mtd/nand/raw/pasemi_nand.c:71:5: warning:
symbol 'pasemi_device_ready' was not declared. Should it be static?
This function is not used outside of pasemi_nand.c, so this commit
marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200721151657.41027-1-weiyongjun1@huawei.com
Now that exec_op() is implemented, we can get rid of all the legacy
hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-7-tudor.ambarus@microchip.com
Use the nand_{write,read}_data_op() helpers instead of calling the
atmel_nand_{read,write}_buf() functions directly. This will ease the
transition to exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-4-tudor.ambarus@microchip.com
No need to enable it everytime select_chip() is called. If we really
care about PM, we should implement runtime PM hooks and disable the
controller and all its clocks when the controller has been unused for
some time.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-2-tudor.ambarus@microchip.com
Many helpers are generic to all NAND chips, they should not be
raw-NAND specific, so use the generic ones.
To avoid moving all the raw NAND core "history" into the generic NAND
layer, we keep a part of this parsing in the raw NAND core to ensure
backward compatibility.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-20-miquel.raynal@bootlin.com
As warned by Sphinx:
./Documentation/gpu/drm-kms-helpers:305: ./include/drm/drm_dsc.h:587: WARNING: Unparseable C cross-reference: 'struct'
Invalid C declaration: Expected identifier in nested name, got keyword: struct [error at 6]
struct
------^
The markup for one struct is wrong, as struct is used twice.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/3d467022325e15bba8dcb13da8fb730099303266.1601467849.git.mchehab+huawei@kernel.org
Also partially revert the follow-up change "drm: pl111: Absorb the
external register header".
This reverts the parts of commits
7e4e589db7 and
0fb8125635 that touch paths outside
of drivers/gpu/drm/pl111.
The fbdev driver is used by Android's FVP configuration. Using the
DRM driver together with DRM's fbdev emulation results in a failure
to boot Android. The root cause is that Android's generic fbdev
userspace driver relies on the ability to set the pixel format via
FBIOPUT_VSCREENINFO, which is not supported by fbdev emulation.
There have been other less critical behavioral differences identified
between the fbdev driver and the DRM driver with fbdev emulation. The
DRM driver exposes different values for the panel's width, height and
refresh rate, and the DRM driver fails a FBIOPUT_VSCREENINFO syscall
with yres_virtual greater than the maximum supported value instead
of letting the syscall succeed and setting yres_virtual based on yres.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929195344.2219796-1-pcc@google.com
Nathan popped up on #xfs and pointed out that we fail to handle
finobt btree blocks in xlog_recover_get_buf_lsn(). This means they
always fall through the entire magic number matching code to "recover
immediately". Whilst most of the time this is the correct behaviour,
occasionally it will be incorrect and could potentially overwrite
more recent metadata because we don't check the LSN in the on disk
metadata at all.
This bug has been present since the finobt was first introduced, and
is a potential cause of the occasional xfs_iget_check_free_state()
failures we see that indicate that the inode btree state does not
match the on disk inode state.
Fixes: aafc3c2465 ("xfs: support the XFS_BTNUM_FINOBT free inode btree type")
Reported-by: Nathan Scott <nathans@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
gfxoff is temporarily disabled for navy_flounder, since
at present the feature caused some tdr when performing
display operations.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the dpm clock table is needed during DC HW initialization.
And that (DC HW initialization) comes before smu_late_init()
where current APU dpm clock table setup is performed. So, NULL
pointer dereference will be triggered. By moving APU dpm clock
table setup to smu_hw_init(), this can be avoided.
Fixes: 02cf91c113 ("drm/amd/powerplay: postpone operations not required for hw setup to late_init")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It has been discovered that there is a potential deadlock between
the clock-change-notifier thread and the UART port suspending one:
CPU0 (suspend CPU/UART) CPU1 (update clock)
---- ----
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
*** DEADLOCK ***
The best way to fix this is to eliminate the CPU0
port->mutex/work-completion scenario. So we suggest to register and
unregister the clock-notifier during the DW APB UART port probe/remove
procedures, instead of doing that at the points of the port
startup/shutdown.
Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com
Fixes: cc816969d7 ("serial: 8250_dw: Fix common clocks usage race condition")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is erroneous to update the TTY port baud rate if it hasn't been
initialized yet, because in that case the TTY struct isn't set. So there
is no termios structure to get and re-calculate the baud if the current
baud can't be reached. Let's skip the baud rate update then until the port
is fully initialized.
Note the update UART clock method still sets the uartclk member with a new
ref clock value even if the port is turned off. The new UART ref clock
rate will be used later on the port starting up procedure.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been a mistake to add the MCR register RTS/DTS fields setting in
the generic method of the UART reference clock update. There is no point
in asserting these lines at that procedure. Just discard the
serial8250_out_MCR() mathod invocation from there then.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that in older systems we get it in the mmap flags scnprintf routines:
$ tools/perf/trace/beauty/mmap_flags.sh | head -9 2> /dev/null
static const char *mmap_flags[] = {
[ilog2(0x40) + 1] = "32BIT",
#ifndef MAP_32BIT
#define MAP_32BIT 0x40
#endif
[ilog2(0x01) + 1] = "SHARED",
#ifndef MAP_SHARED
#define MAP_SHARED 0x01
#endif
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The board uses lane 3 of SERDES for USB. Set the mux
accordingly.
The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, QSGMII and USB super-speed. It has been
chosen to use PCI2 and QSGMII as default. So restrict
USB0 to high-speed mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-7-rogerq@ti.com
First two lanes of SERDES is connected to PCIe, third lane is
connected to QSGMII and the last lane is connected to USB. However,
Cadence torrent SERDES doesn't support more than 2 protocols
at the same time. Configure it only for PCIe and QSGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-6-rogerq@ti.com
The USB controller can be connected to one of the 2 lanes
of SERDES0 using a MUX. Add a MUX controller node for that.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-4-rogerq@ti.com
The SERDES lane control mux registers are present in the
CTRLMMR space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-3-rogerq@ti.com
There are 4 lanes in each J7200 SERDES. Each SERDES lane mux can
select upto 4 different IPs. Define all the possible functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200930122032.23481-2-rogerq@ti.com
The IPG clock is disabled at the end of imx_uart_shutdown(); we really
don't want to run any IRQ handlers after this point.
At least on i.MX8MN, the UART will happily continue to generate interrupts
even with its clocks disabled, but in this state, all register writes are
ignored (which will cause the shadow registers to differ from the actual
register values, resulting in all kinds of weirdness).
In a transfer without DMA, this could lead to the following sequence of
events:
- The UART finishes its transmission while imx_uart_shutdown() is run,
triggering the TXDC interrupt (we can trigger this fairly reliably by
writing a single byte to the TTY and closing it right away)
- imx_uart_shutdown() finishes, disabling the UART clocks
- imx_uart_int() -> imx_uart_transmit_buffer() -> imx_uart_stop_tx()
imx_uart_stop_tx() should now clear UCR4_TCEN to disable the TXDC
interrupt, but this register write is ineffective. This results in an
interrupt storm.
To disable all interrupts in the same place, and to avoid setting UCR4
twice, clearing UCR4_OREN is moved below del_timer_sync() as well; this
should be harmless.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200925082412.12960-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the port of the commit db1b5bc047 ("serial: 8250: Fix TX
interrupt handling condition") to the 8250_fsl irq handling logic.
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Andrij Abyzov <aabyzov@slb.com>
Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:
| sysrq: Changing Loglevel
| sysrq: Loglevel set to 9
|
| ======================================================
| WARNING: possible circular locking dependency detected
| 5.9.0-rc7 #1 Not tainted
| ------------------------------------------------------
| systemd-journal/138 is trying to acquire lock:
| ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
|
| but task is already holding lock:
| ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
|
| which lock already depends on the new lock.
[...]
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock(&port_lock_key);
| lock(console_owner);
| lock(&port_lock_key);
| lock(console_owner);
|
| *** DEADLOCK ***
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2nd and 3rd parameter were wrongly used, and cause kernel abort when
doing kgdb debug.
Fixes: 1da17d7cf8 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Add vendor suffix to all proprietary properties.
2. Fix typo.
3. Change lsw to normal property, not pattern property.
4. Due to item 1, modify source code for property parsing.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1601460480-4259-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
@setup_text_buf only copies the original text messages (without any
prefix or extended text). It only needs to be LOG_LINE_MAX in size.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200930090134.8723-3-john.ogness@linutronix.de
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-14-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a reader provides a buffer that is smaller than the message text,
the @text_len field of @info will have a value larger than the buffer
size. If readers blindly read @text_len bytes of data without
checking the size, they will read beyond their buffer.
Add this check to record_print_text() to properly recognize when such
truncation has occurred.
Add a maximum size argument to the ringbuffer function to extend
records so that records can not be created that are larger than the
buffer size of readers.
When extending records (LOG_CONT), do not extend records beyond
LOG_LINE_MAX since that is the maximum size available in the buffers
used by consoles and syslog.
Fixes: f5f022e53b ("printk: reimplement log_cont using record extension")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200930090134.8723-2-john.ogness@linutronix.de
If the caller of enable_callback_mst() passes a cb func, the callee
function will malloc memory and link this cb func to the list
unconditionally. This will introduce problem if caller is in the
hda_codec_ops.init() since the init() will be repeatedly called in the
codec rt_resume().
So far, the patch_hdmi.c and patch_ca0132.c call enable_callback_mst()
in the hda_codec_ops.init().
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200930055146.5665-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
arch/s390/pci/pci_bus.h: zpci_bus_init - only declaration left after
commit 05bc1be6db ("s390/pci: create zPCI bus")
arch/s390/include/asm/gmap.h: gmap_pte_notify - only declaration left
after commit 4be130a084 ("s390/mm: add shadow gmap support")
arch/s390/include/asm/pgalloc.h: rcu_table_freelist_finish - only
declaration left after commit 36409f6353 ("[S390] use generic RCU
page-table freeing code")
arch/s390/include/asm/tlbflush.h: smp_ptlb_all - only declaration left
after commit 5a79859ae0 ("s390: remove 31 bit support")
arch/s390/include/asm/vtimer.h: init_cpu_vtimer - only declaration left
after commit b5f87f15e2 ("s390/idle: consolidate idle functions and
definitions")
arch/s390/include/asm/pci.h: zpci_debug_info - only declaration left
after commit 386aa051fb ("s390/pci: remove per device debug attribute")
arch/s390/include/asm/vdso.h: vdso_alloc_boot_cpu - only declaration
left after commit 4bff8cb545 ("s390: convert to GENERIC_VDSO")
arch/s390/include/asm/smp.h: smp_vcpu_scheduled - only declaration left
after commit 67626fadd2 ("s390: enforce CONFIG_SMP")
arch/s390/kernel/entry.h: restart_call_handler - only declaration left
after commit 8b646bd759 ("[S390] rework smp code")
arch/s390/kernel/entry.h: startup_init_nobss - only declaration left
after commit 2e83e0eb85 ("s390: clean .bss before running uncompressed
kernel")
arch/s390/kernel/entry.h: s390_early_resume - only declaration left after
commit 394216275c ("s390: remove broken hibernate / power management
support")
drivers/s390/char/raw3270.h: raw3270_request_alloc_bootmem - only
declaration left after commit 33403dcfcd ("[S390] 3270 console:
convert from bootmem to slab")
drivers/s390/cio/device.h: ccw_device_schedule_sch_unregister - only
declaration left after commit 37de53bb52 ("[S390] cio: introduce ccw
device todos")
drivers/s390/char/tape.h: tape_hotplug_event - has only declaration
since recorded git history.
drivers/s390/char/tape.h: tape_oper_handler - has only declaration since
recorded git history.
drivers/s390/char/tape.h: tape_noper_handler - has only declaration
since recorded git history.
drivers/s390/char/tape_std.h: tape_std_check_locate - only declaration
left after commit 161beff8f4 ("s390/tape: remove tape block leftovers")
drivers/s390/char/tape_std.h: tape_std_default_handler - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_unexpect_uchk_handler - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_irq - has only declaration since
recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_has_failed -
has only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_succeded - has
only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_do_retry - has
only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_read_opposite -
has only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_HWBUG - has only
declaration since recorded git history.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
startup pgm check handler is active since the very beginning of kernel
code execution until uncompressed kernel sets up s390_base_pgm_handler.
It is useful not just for the decompressor debugging itself, but also for
early code of uncompressed kernel, in particular Kasan initialization. But
since there is no stack trace or symbolic representation of failing psw
address it is impossible to figure out faulty code location without
knowing Kaslr kernel base. So, let's add it to the startup pgm check
info printed as well.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
sclp_set_columns and sclp_set_htab are leftovers since commit 095761d28a
("[S390] sclp_tty: remove ioctl interface."), remove them as a dead code.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
