vxlan_xmit_one() was only called from vxlan_xmit() without rdst and
info was already tested. Emit warning in that function instead
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
small optimization around checking as it's being done in all
receptions
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
call vxlan_remcsum() before md filling in vxlan_rcv()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start also "phy state machine", with UP state as it should be,
the phy_start() has to be used, in another case machine even is not
triggered. After this change negotiation is supposed to be triggered
by SM workqueue.
It's not correct usage, but it appears after the following patch,
so add it as a fix.
Fixes: 74a992b359 ("net: phy: add phy_check_link_status")
Signed-off-by: Ivan Khoronzhuk <ikhoronz@cisco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should remove a group from the sg_port hash only if it's an S,G
entry. This makes it correct and more symmetric with group add. Also
since *,G groups are not added to that hash we can hide a bug.
Fixes: 085b53c8be ("net: bridge: mcast: add sg_port rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.
Removing the second call of clk_disable_unprepare() in
intel_eth_pci_remove().
Fixes: 09f012e64e ("stmmac: intel: Fix clock handling on error and remove paths")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.
When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
will pass up all rx packets that failed address filtering (similar to
promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
filters and get routed to selected VFFQ Rx queue.
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we AND two values together that are known in the 32bit subregs, but not
known in the 64bit registers we rely on the tnum value to report the 32bit
subreg is known. And do not use mark_reg_known() directly from
scalar32_min_max_and()
Add an AND test to cover the case with known 32bit subreg, but unknown
64bit reg.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In BPF_AND and BPF_OR alu cases we have this pattern when the src and dst
tnum is a constant.
1 dst_reg->var_off = tnum_[op](dst_reg->var_off, src_reg.var_off)
2 scalar32_min_max_[op]
3 if (known) return
4 scalar_min_max_[op]
5 if (known)
6 __mark_reg_known(dst_reg,
dst_reg->var_off.value [op] src_reg.var_off.value)
The result is in 1 we calculate the var_off value and store it in the
dst_reg. Then in 6 we duplicate this logic doing the op again on the
value.
The duplication comes from the the tnum_[op] handlers because they have
already done the value calcuation. For example this is tnum_and().
struct tnum tnum_and(struct tnum a, struct tnum b)
{
u64 alpha, beta, v;
alpha = a.value | a.mask;
beta = b.value | b.mask;
v = a.value & b.value;
return TNUM(v, alpha & beta & ~v);
}
So lets remove the redundant op calculation. Its confusing for readers
and unnecessary. Its also not harmful because those ops have the
property, r1 & r1 = r1 and r1 | r1 = r1.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the inner
offload capability is to be restrictued to UDP tunnels.
This patch fixes the issue for non-udp tunnels by adding features
check capability and filtering appropriate features for non-udp tunnels.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Devlink regions for SJA1105 DSA driver
This series exposes the SJA1105 static config as a devlink region. This
can be used for debugging, for example with the sja1105_dump user space
program that I have derived from Andrew Lunn's mv88e6xxx_dump:
https://github.com/vladimiroltean/mv88e6xxx_dump/tree/sja1105
Changes in v2:
- Tear down devlink params on initialization failure.
- Add driver identification through devlink.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the driver name and ASIC ID so that generic user space
application are able to know they're looking at sja1105 devlink regions
when pretty-printing them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in Documentation/networking/dsa/sja1105.rst, this switch
has a static config held in the driver's memory and re-uploaded from
time to time into the device (after any major change).
The format of this static config is in fact described in UM10944.pdf and
it contains all the switch's settings (it also contains device ID, table
CRCs, etc, just like in the manual). So it is a useful and universal
devlink region to expose to user space, for debugging purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll have more devlink code soon. Group it together in a separate
translation object.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg says:
====================
make drivers/net/ethernet W=1 clean
The Goal: move to W=1 being default for drivers/net/ethernet, and
then use automation to catch more code issues (warnings) being
introduced.
The status: Getting much closer but not quite done for all
architectures.
After applying the patches below, the drivers/net/ethernet
directory can be built as modules with W=1 with no warnings (so
far on x64_64 arch only!). As Jakub pointed out, there is much
more work to do to clean up C=1, but that will be another series
of changes.
This series removes 1,247 warnings and hopefully allows the
ethernet directory to move forward from here without more
warnings being added. There is only one objtool warning now.
This version drops one of the Intel patches, as I couldn't
reproduce the original issue to document the warning.
Some of these patches are already sent and tested on Intel Wired
Lan, but the rest of the series titled drivers/net/ethernet
affects other drivers. The changes are all pretty
straightforward.
====================
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel-doc script as used by W=1, is confused by the macro
usage inside the header describing the efx_ptp_data struct.
drivers/net/ethernet/sfc/ptp.c:345: warning: Function parameter or member 'MC_CMD_PTP_IN_TRANSMIT_LENMAX' not described in 'efx_ptp_data'
After some discussion on the list, break this patch out to
a separate one, and fix the issue through a creative
macro declaration.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 series for ethernet, these drivers were
discovered to be using kdoc style comments but were not actually
doing kdoc. The kernel uses kdoc style when documenting code, not
doxygen or other styles.
Fixed Warnings:
drivers/net/ethernet/amazon/ena/ena_com.c:613: warning: Function parameter or member 'ena_dev' not described in 'ena_com_set_llq'
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c:1540: warning: Cannot understand * @brief Set VLAN filter table
drivers/net/ethernet/xilinx/ll_temac_main.c:114: warning: Function parameter or member 'lp' not described in 'temac_indirect_busywait'
drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32'
drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32'
drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'value' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'value' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'lp' not described in 'temac_dma_in32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'reg' not described in 'temac_dma_in32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'lp' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'reg' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'value' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_in'
drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_in'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'value' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'lp' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'op' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'np' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:300: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_release'
drivers/net/ethernet/xilinx/ll_temac_main.c:330: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_init'
drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'ndev' not described in 'temac_setoptions'
drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'options' not described in 'temac_setoptions'
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of drivers had a "generic documentation" section that
would trigger a "can't understand" message from W=1 compiles.
Fix by using correct DOC: tags in the generic sections.
Fixed Warnings:
drivers/net/ethernet/arc/emac_arc.c:4: info: Scanning doc for c
drivers/net/ethernet/cadence/macb_pci.c:3: warning: missing initial short description on line:
* Cadence GEM PCI wrapper.
drivers/net/ethernet/cadence/macb_pci.c:3: info: Scanning doc for Cadence
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While fixing the W=1 builds, this warning came up because the
developers used a very tricky way to get structures initialized
to a non-zero value, but this causes GCC to warn about an
override. In this case the override was intentional, so just
disable the warning for this code with a kernel macro that results
in disabling the warning for compiles on GCC versions after 8.
It is not appropriate to change the struct to initialize all the
values as it will just add a lot more code for no value. The code
is completely correct as is, we just want to acknowledge that
this code could generate a warning and we're ok with that.
NOTE: the __diag_ignore macro currently only accepts a second
argument of 8 (version 80000), it's either use this one or
open code the pragma.
Fixed Warnings example (all the same):
drivers/net/ethernet/renesas/sh_eth.c:51:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:52:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:53:13: warning: initialized field overwritten [-Woverride-init]
+ 256 more...
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The W=1 builds showed a few files exporting functions
(non-static) that were not prototyped. What actually happened is
that there were prototypes, but the include file was forgotten in
the implementation file.
Add the include file and remove the warnings.
Fixed Warnings:
drivers/net/ethernet/cavium/liquidio/cn68xx_device.c:124:5: warning: no previous prototype for ‘lio_setup_cn68xx_octeon_device’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:159:1: warning: no previous prototype for ‘octeon_pci_read_core_mem’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:168:1: warning: no previous prototype for ‘octeon_pci_write_core_mem’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:176:5: warning: no previous prototype for ‘octeon_read_device_mem64’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:185:5: warning: no previous prototype for ‘octeon_read_device_mem32’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:194:6: warning: no previous prototype for ‘octeon_write_device_mem32’ [-Wmissing-prototypes]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_dcb.c:453:6: warning: no previous prototype for ‘hclge_dcb_ops_set’ [-Wmissing-prototypes]
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove variables that were storing a return value from a register
read or other read, where the return value wasn't used. Those
conversions to remove the lvalue of the assignment should be safe
because the readl memory mapped reads are marked volatile and
should not be optimized out without an lvalue (I suspect a very
long time ago this wasn't guaranteed as it is today).
These changes are part of a separate patch to make it easier to review.
Warnings Fixed:
.../intel/e100.c:2596:9: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:101:6: warning: variable ‘icr_reg’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:277:6: warning: variable ‘ctrl_reg’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:952:15: warning: variable ‘temp_reg’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:1164:7: warning: variable ‘mdio_reg’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:132:6: warning: variable ‘ret_val’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:380:6: warning: variable ‘icr’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:2378:6: warning: variable ‘signal’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:2374:6: warning: variable ‘ctrl’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:2373:6: warning: variable ‘rxcw’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:4678:15: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-09-25
This series contains updates to the iavf and ice driver.
Sylwester fixes a crash with iavf resume due to getting the wrong pointers.
Ani fixes a call trace in ice resume by calling pci_save_state().
Jakes fixes memory leaks in case of register_netdev() failure or
ice_cfg_vsi_lan() failure for the ice driver.
v2: Rebased; no other changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A small collection of driver specific fixes, the fsl-espi and bcm-qspi
changes in particular have been causing breakage for users.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uS/ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HO5B/kBy15WzYCeJ1VqAq+HXliT8IvFuGMh
GgwIggHFRpqH9DBMA3PxrjHF9ULfu7wGA2hrSE6Mn2Cxnbt3qsPMU57yRuer9Zb9
ngWNID2BpbyWtXvwDcV7e+0N9ahsgynQR9aJ7JTRfhDBwsHSz9IWF+i6Aug0/I1Z
tDlEm8vhpIJcWuFKX1W7P1pLJ0y/1dqQHQh6vGajuj3c9EOuyrF1BjarfnhhokXL
iB3wdSaj6OAUmkvM4/fZdZrgMDtSoYurDSSTnl4XQPHavwqXbg64s57x/l25ye8N
Zz9lsH9nHCSrBPUnbAI4NpwlQtFx6z7aLUGJp7rcU2OSiSn6QnNc6ycF
=1ejb
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of driver specific fixes, the fsl-espi and bcm-qspi
changes in particular have been causing breakage for users"
* tag 'spi-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bcm-qspi: Fix probe regression on iProc platforms
spi: fsl-dspi: fix use-after-free in remove path
spi: fsl-espi: Only process interrupts for expected events
spi: bcm2835: Make polling_limit_us static
spi: spi-fsl-dspi: use XSPI mode instead of DMA for DPAA2 SoCs
A single fix for incorrect specification of some of the register fields
on axp20x devices which would break voltage setting on affected systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uTFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OEZB/9tRSg6gHVdp2OwAbWPzJQcHYYP4stQ
H3mPcsDJRmpVnHhUQe3qlUvG4QZ7bDhnHFYS1G7LFgEBNVhCwKtpnseaQMJaCaa+
t9LLWNtzltuo75995bBtPYcSQI6U0yUYbu7U7n+4vibh/pjqY3eNg4lLrWtVL/OC
FwkCEql5+ZTTg3OcRHzKlYe1UlOB0kSHNCjySiVytPrC0UH32gFCs/LSZxDR8lbo
a9x8Vi8brbcmpASoCY0d+c0hM6PWB/chNwVHGnoWYJ+xoJMVLzC8TN/mkUgG++9i
wnwXfbUd0EbLKuLrZto0qdx14n2nLp2YpeLJhTbsJaQ5C+FQGvv7D2v5
=Uvnh
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A single fix for incorrect specification of some of the register
fields on axp20x devices which would break voltage setting on affected
systems"
* tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: axp20x: fix LDO2/4 description
Two issues here - one is a fix for use after free issues in the case
where a regmap overrides its name using something dynamically generated,
the other is that we weren't handling access checks non-incrementing I/O
on registers within paged register regions correctly resulting in
spurious errors. Both of these are quite rare but serious if they
occur.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uTagTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HQ0B/9rfdPyuAxvv21vDoQbVYI8vg98WOGg
gB+JJ1WKt9o6H3R64k8drgGB1DL/vWTub2+bkIoey0XMmIOsADBq/qrWeX4ziwpl
LhkDxBbTc1U0Wqkq2IONjQbp9pr4kJyoTxGc6BRyysO0TAcfrGD5JvSRru9SLiSc
cWpLq6YgL1KoLSEcvy5B7n9TydCEtNw8CpnalLvxFtmlthelFFHkCZmt2+R2fYVa
QsNGEPlmsiKEL7KXlnGrDcNsnJ59YBAicsaPMBUk0tGkbNt5ifdsSxUJbCmAV+41
yCt5QIlf0Ctjhb7m/Xm4efIOKbmyhGPmG7ZdrZMRXmmcLshFfxJkd+k+
=0+l/
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two issues here - one is a fix for use after free issues in the case
where a regmap overrides its name using something dynamically
generated, the other is that we weren't handling access checks
non-incrementing I/O on registers within paged register regions
correctly resulting in spurious errors.
Both of these are quite rare but serious if they occur"
* tag 'regmap-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix page selection for noinc writes
regmap: fix page selection for noinc reads
regmap: debugfs: Add back in erroneously removed initialisation of ret
regmap: debugfs: Fix handling of name string for debugfs init delays
Since only the v4 code cares about it, maybe it's better to leave
rq_lease_breaker out of the common dispatch code?
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There are actually rare races where this is possible (e.g. if a new open
intervenes between the read of i_writecount and the fi_fds).
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The nfsd open code has always kept separate read-only, read-write, and
write-only opens as necessary to ensure that when a client closes or
downgrades, we don't retain more access than necessary.
Also, I didn't realize the cache behaved this way when I wrote
94415b06eb "nfsd4: a client's own opens needn't prevent delegations".
There I assumed fi_fds[O_WRONLY] and fi_fds[O_RDWR] would always be
distinct. The violation of that assumption is triggering a
WARN_ON_ONCE() and could also cause the server to give out a delegation
when it shouldn't.
Fixes: 94415b06eb ("nfsd4: a client's own opens needn't prevent delegations")
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Is it just me, or is the logic written in a slightly convoluted way?
I find it a little easier to read this way.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
As more use cases of checking if a tracepoint is enabled in a header are
coming to fruition, a helper macro, tracepoint_enabled(), has been added to
check if a tracepoint is enabled or not, and can be used with minimal header
requirements (avoid "include hell"). Convert the page_ref logic over to the
new helper macro.
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As tracepoints are discouraged from being added in a header because it can
cause side effects if other tracepoints are in headers, as well as bloat the
kernel as the trace_<tracepoint>() function is not a small inline, the common
workaround is to add a function call that calls a wrapper function in a
C file that then calls the tracepoint. But as function calls add overhead,
this function should only be called when the tracepoint in question is
enabled. To get around this overhead, a static_branch can be used to only
have the tracepoint wrapper get called when the tracepoint is enabled.
Add a tracepoint_enabled(tp) macro that gets passed the name of the
tracepoint, and this becomes a static_branch that is enabled when the
tracepoint is enabled and is a nop when the tracepoint is disabled.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
seq_puts is a lot cheaper than seq_printf, so use that to print
literal strings.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
silence nfscache allocation warnings with kvzalloc
Currently nfsd_reply_cache_init attempts hash table allocation through
kmalloc, and manually falls back to vzalloc if that fails. This makes
the code a little larger than needed, and creates a significant amount
of serial console spam if you have enough systems.
Switching to kvzalloc gets rid of the allocation warnings, and makes
the code a little cleaner too as a side effect.
Freeing of nn->drc_hashtbl is already done using kvfree currently.
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Fixes coccicheck warning:
fs/nfsd/nfs4proc.c:3234:5-29: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Squelch some sparse warnings:
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:1860:16: warning: incorrect type in assignment (different base types)
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:1860:16: expected int status
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:1860:16: got restricted __be32
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:1862:24: warning: incorrect type in return expression (different base types)
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:1862:24: expected restricted __be32
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:1862:24: got int status
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Squelch some sparse warnings:
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4692:24: warning: incorrect type in return expression (different base types)
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4692:24: expected int
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4692:24: got restricted __be32 [usertype]
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4702:32: warning: incorrect type in return expression (different base types)
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4702:32: expected int
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4702:32: got restricted __be32 [usertype]
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4739:13: warning: incorrect type in assignment (different base types)
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4739:13: expected restricted __be32 [usertype] err
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4739:13: got int
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4891:15: warning: incorrect type in assignment (different base types)
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4891:15: expected unsigned int [assigned] [usertype] count
/home/cel/src/linux/linux/fs/nfsd/nfs4xdr.c:4891:15: got restricted __be32 [usertype]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Squelch some sparse warnings:
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2264:13: warning: incorrect type in assignment (different base types)
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2264:13: expected int err
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2264:13: got restricted __be32
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2266:24: warning: incorrect type in return expression (different base types)
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2266:24: expected restricted __be32
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2266:24: got int err
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2288:13: warning: incorrect type in assignment (different base types)
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2288:13: expected int err
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2288:13: got restricted __be32
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2290:24: warning: incorrect type in return expression (different base types)
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2290:24: expected restricted __be32
/home/cel/src/linux/linux/fs/nfsd/vfs.c:2290:24: got int err
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Reserving space for a large READ payload requires special handling when
reserving space in the xdr buffer pages. One problem we can have is use
of the scratch buffer, which is used to get a pointer to a contiguous
region of data up to PAGE_SIZE. When using the scratch buffer, calls to
xdr_commit_encode() shift the data to it's proper alignment in the xdr
buffer. If we've reserved several pages in a vector, then this could
potentially invalidate earlier pointers and result in incorrect READ
data being sent to the client.
I get around this by looking at the amount of space left in the current
page, and never reserve more than that for each entry in the read
vector. This lets us place data directly where it needs to go in the
buffer pages.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Now when a read delegation is given, two delegation related traces
will be printed:
nfsd_deleg_open: client 5f45b854:e6058001 stateid 00000030:00000001
nfsd_deleg_none: client 5f45b854:e6058001 stateid 0000002f:00000001
Although the intention is to let developers know two stateid are
returned, the traces are confusing about whether or not a read delegation
is handled out. So renaming trace_nfsd_deleg_none() to trace_nfsd_open()
and trace_nfsd_deleg_open() to trace_nfsd_deleg_read() to make
the intension clearer.
The patched traces will be:
nfsd_deleg_read: client 5f48a967:b55b21cd stateid 00000003:00000001
nfsd_open: client 5f48a967:b55b21cd stateid 00000002:00000001
Suggested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It struck me while watching Jon Corbet ask how to keep kernel
Documentation up to date, that it might help if we were actually cc'd on
Documentation/filesystems/nfs/ changes.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In nfsd4_encode_listxattrs(), the variable p is assigned to at one point
but this value is never used before p is reassigned. Fix this.
Addresses-Coverity: ("Unused value")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Drop duplicate words in net/sunrpc/.
Also fix "Anyone" to be "Any one".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The delegation is no longer returnable, so I don't think there's much
point retrying the recall.
(I think it's worth asking why we even need separate CLOSED_DELEG and
REVOKED_DELEG states. But treating them the same would currently cause
nfsd4_free_stateid to call list_del_init(&dp->dl_recall_lru) on a
delegation that the laundromat had unhashed but not revoked, incorrectly
removing it from the laundromat's reaplist or a client's dl_recall_lru.)
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It was an interesting idea but nobody seems to be using it, it's buggy
at this point, and nfs4state.c is already complicated enough without it.
The new nfsd/clients/ code provides some of the same functionality, and
could probably do more if desired.
This feature has been deprecated since 9d60d93198 ("Deprecate nfsd
fault injection").
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
