Remove prefix 'CONFIG_' from CONFIG_IPV6
Fixes: ba7d7e2677 ("net/rds/Kconfig: RDS should depend on IPV6")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Support DSCP prioritization and rewrite
Petr says:
On ingress, a network device such as a switch assigns to packets
priority based on various criteria. Common options include interpreting
PCP and DSCP fields according to user configuration. When a packet
egresses the switch, a reverse process may rewrite PCP and/or DSCP
headers according to packet priority.
So far, mlxsw has supported prioritization based on PCP (802.1p priority
tag). This patch set introduces support for prioritization based on
DSCP, and DSCP rewrite.
To configure the DSCP-to-priority maps, the user is expected to invoke
ieee_setapp and ieee_delapp DCBNL ops, e.g. by using lldptool:
To decide whether or not to pay attention to DSCP values, the Spectrum
switch recognize a per-port configuration of trust level. Until the
first APP rule is added for a given port, this port's trust level stays
at PCP, meaning that PCP is used for packet prioritization. With the
first DSCP APP rule, the port is configured to trust DSCP instead, and
it stays there until all DSCP APP rules are removed again.
Besides the DSCP (value 5) selector, another selector that plays into
packet prioritization is Ethernet type (value 1) with PID of 0. Such APP
entries denote default priority[1]:
With this patch set, mlxsw uses these values to configure priority for
DSCP values not explicitly specified in DSCP APP map. In the future we
expect to also use this to configure default port priority for untagged
packets.
Access to DSCP-to-priority map, priority-to-DSCP map, and default
priority for a port is exposed through three new DCB helpers. Like the
already-existing dcb_ieee_getapp_mask() helper, these helpers operate in
terms of bitmaps, to support the arbitrary M:N mapping that the APP
rules allow. Such interface presents all the relevant information from
the APP database without necessitating exposition of iterators, locking
or other complex primitives. It is up to the driver to then digest the
mapping in a way that the device supports. In this patch set, mlxsw
resolves conflicts by favoring higher-numbered DSCP values and
priorities.
In this patchset:
- Patch #1 fixes a bug in DCB APP database management.
- Patch #2 adds the getters described above.
- Patches #3-#6 add Spectrum configuration registers.
- Patch #7 adds the mlxsw logic that configures the device according to
APP rules.
- Patch #8 adds a self-test. The test is added to the subdirectory
drivers/net/mlxsw. Even though it's not particularly specific to
mlxsw, it's not suitable for running on soft devices (which don't
support the ieee_getapp et.al.), and thus isn't a good fit for the
general net/forwarding directory.
[1] 802.1Q-2014, Table D-9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that exercises the new code. Send DSCP-tagged packets, and
observe how they are prioritized in the switch and the DSCP is updated
on egress again.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APP TLVs are used for communicating priority-to-protocol ID maps for
a given netdevice. Support the following APP TLVs:
- DSCP (selector 5) to configure priority-to-DSCP code point maps. Use
these maps to configure packet priority on ingress, and DSCP code
point rewrite on egress.
- Default priority (selector 1, PID 0) to configure priority for the
DSCP code points that don't have one assigned by the DSCP selector. In
future this could also be used for assigning default port priority
when a packet arrives without DSCP tagging.
Besides setting up the maps themselves, also configure port trust level
and rewrite bits.
Port trust level determines whether, for a packet arriving through a
certain port, the priority should be determined based on PCP or DSCP
header fields. So far, mlxsw kept the device default of trust-PCP. Now,
as soon as the first DSCP APP TLV is configured, switch to trust-DSCP.
Only when all DSCP APP TLVs are removed, switch back to trust-PCP again.
Note that the default priority APP TLV doesn't impact the trust level
configuration.
Rewrite bits determine whether DSCP and PCP fields of egressing packets
should be updated according to switch priority. When port trust is
switched to DSCP, enable rewrite of DSCP field.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register controls mapping from Priority to DSCP for purposes of
rewrite. Note that rewrite happens as the packet is transmitted provided
that the DSCP rewrite bit is enabled for the packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the rewrite enable (whether PCP or DSCP value
in packet should be updated according to packet priority) per receive
port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPTS register controls the port policy to calculate the switch
priority and packet color based on incoming packet fields.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPDPM register controls the mapping from DSCP field to Switch
Priority for IP packets.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ingress, a network device such as a switch assigns to packets
priority based on various criteria. Common options include interpreting
PCP and DSCP fields according to user configuration. When a packet
egresses the switch, a reverse process may rewrite PCP and/or DSCP
values according to packet priority.
The following three functions support a) obtaining a DSCP-to-priority
map or vice versa, and b) finding default-priority entries in APP
database.
The DCB subsystem supports for APP entries a very generous M:N mapping
between priorities and protocol identifiers. Understandably,
several (say) DSCP values can map to the same priority. But this
asymmetry holds the other way around as well--one priority can map to
several DSCP values. For this reason, the following functions operate in
terms of bitmaps, with ones in positions that match some APP entry.
- dcb_ieee_getapp_dscp_prio_mask_map() to compute for a given netdevice
a map of DSCP-to-priority-mask, which gives for each DSCP value a
bitmap of priorities related to that DSCP value by APP, along the
lines of dcb_ieee_getapp_mask().
- dcb_ieee_getapp_prio_dscp_mask_map() similarly to compute for a given
netdevice a map from priorities to a bitmap of DSCPs.
- dcb_ieee_getapp_default_prio_mask() which finds all default-priority
rules for a given port in APP database, and returns a mask of
priorities allowed by these default-priority rules.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function dcb_app_lookup walks the list of specified DCB APP entries,
looking for one that matches a given criteria: ifindex, selector,
protocol ID and optionally also priority. The "don't care" value for
priority is set to 0, because that priority has not been allowed under
CEE regime, which predates the IEEE standardization.
Under IEEE, 0 is a valid priority number. But because dcb_app_lookup
considers zero a wild card, attempts to add an APP entry with priority 0
fail when other entries exist for a given ifindex / selector / PID
triplet.
Fix by changing the wild-card value to -1.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for today we don't setup SMP_CACHE_BYTES and cache_line_size for
ARC, so they are set to L1_CACHE_BYTES by default. L1 line length
(L1_CACHE_BYTES) might be easily smaller than L2 line (which is
usually the case BTW). This breaks code.
For example this breaks ethernet infrastructure on HSDK/AXS103 boards
with IOC disabled, involving manual cache flushes
Functions which alloc and manage sk_buff packet data area rely on
SMP_CACHE_BYTES define. In the result we can share last L2 cache
line in sk_buff linear packet data area between DMA buffer and
some useful data in other structure. So we can lose this data when
we invalidate DMA buffer.
sk_buff linear packet data area
|
|
| skb->end skb->tail
V | |
V V
----------------------------------------------.
packet data | <tail padding> | <useful data in other struct>
----------------------------------------------.
---------------------.--------------------------------------------------.
SLC line | SLC (L2 cache) line (128B) |
---------------------.--------------------------------------------------.
^ ^
| |
These cache lines will be invalidated when we invalidate skb
linear packet data area before DMA transaction starting.
This leads to issues painful to debug as it reproduces only if
(sk_buff->end - sk_buff->tail) < SLC_LINE_SIZE and
if we have some useful data right after sk_buff->end.
Fix that by hardcode SMP_CACHE_BYTES to max line length we may have.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC backend for dma_sync_single_for_(device|cpu) was broken as it was
not honoring the @dir argument and simply forcing it based on the call:
- arc_dma_sync_single_for_device(dir) assumed DMA_TO_DEVICE (cache wback)
- arc_dma_sync_single_for_cpu(dir) assumed DMA_FROM_DEVICE (cache inv)
This is not true given the DMA API programming model and has been
discussed here [1] in some detail.
Interestingly while the deficiency has been there forever, it only started
showing up after 4.17 dma common ops rework, commit a8eb92d02d
("arc: fix arc_dma_{map,unmap}_page") which wired up these calls under the
more commonly used dma_map_page API triggering the issue.
[1]: https://lkml.org/lkml/2018/5/18/979
Fixes: commit a8eb92d02d ("arc: fix arc_dma_{map,unmap}_page")
Cc: stable@kernel.org # v4.17+
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: reworked changelog]
This patch cleans up spaces and align the text to refine the comment for
amdgpu_ttm.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pass the evict flag instead of hard code
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Every set_pages_array_wb call resulted in cross-core
interrupts and TLB flushes. Merge more of them for
less overhead.
This reduces the time needed to free a 1.6 GiB GTT WC
buffer as part of Vulkan CTS from ~2 sec to < 0.25 sec.
(Allocation still takes more than 2 sec though)
(v2): use set_pages_wb instead of set_memory_wb.
Signed-off-by: Bas Nieuwenhuizen <basni@chromium.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All non-x86 definitions are moved to ttm_set_memory header, so remove it from
ttm_page_alloc.c.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Bas Nieuwenhuizen <basni@chromium.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All non-x86 definitions are moved to ttm_set_memory header, so remove it from
ttm_page_alloc_dma.c.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Bas Nieuwenhuizen <basni@chromium.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch moves all non-x86 abstraction to the ttm_set_memory header.
It is to make function calling more clearly.
(v2): add ttm_ prefix.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Bas Nieuwenhuizen <basni@chromium.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=2ogY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180727' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Bigger than usual at this time, mostly due to the O_DIRECT corruption
issue and the fact that I was on vacation last week. This contains:
- NVMe pull request with two fixes for the FC code, and two target
fixes (Christoph)
- a DIF bio reset iteration fix (Greg Edwards)
- two nbd reply and requeue fixes (Josef)
- SCSI timeout fixup (Keith)
- a small series that fixes an issue with bio_iov_iter_get_pages(),
which ended up causing corruption for larger sized O_DIRECT writes
that ended up racing with buffered writes (Martin Wilck)"
* tag 'for-linus-20180727' of git://git.kernel.dk/linux-block:
block: reset bi_iter.bi_done after splitting bio
block: bio_iov_iter_get_pages: pin more pages for multi-segment IOs
blkdev: __blkdev_direct_IO_simple: fix leak in error case
block: bio_iov_iter_get_pages: fix size of last iovec
nvmet: only check for filebacking on -ENOTBLK
nvmet: fixup crash on NULL device path
scsi: set timed out out mq requests to complete
blk-mq: export setting request completion state
nvme: if_ready checks to fail io to deleting controller
nvmet-fc: fix target sgl list on large transfers
nbd: handle unexpected replies better
nbd: don't requeue the same request twice.
Fixes: d284f8248c ("dm writecache: support optional offset for start of device")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In preparing to remove all stack VLA usage from the kernel[1], remove
the discouraged use of AHASH_REQUEST_ON_STACK in favor of the smaller
SHASH_DESC_ON_STACK by converting from ahash-wrapped-shash to direct
shash. The stack allocation will be made a fixed size in a later patch
to the crypto subsystem.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This is a small simplification of dm-crypt - use wake_up_process()
instead of a wait queue in a case where only one process may be
waiting. dm-writecache uses a similar pattern.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When using external metadata device and internal hash, recalculate the
checksums when the device is created - so that dm-integrity doesn't
have to overwrite the device. The superblock stores the last position
when the recalculation ended, so that it is properly restarted.
Integrity tags that haven't been recalculated yet are ignored.
Also bump the target version.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Flush the journal on suspend when using separate data and metadata devices,
so that the metadata device can be discarded and the table can be reloaded
with a linear target pointing to the data device.
NOTE: the journal is deliberately not flushed when using the same device
for metadata and data, so that the journal replay code is tested.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use version "2" in the superblock when data and metadata devices are
separate, so that the device is not accidentally read by older kernel
version.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add the ability to store DM integrity metadata on a separate device.
This feature is activated with the option "meta_device:/dev/device".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A small refactoring. Add the variable ic->start to the result
returned by get_data_sector() and not in the callers. This is a
prerequisite for the commit that adds the ability to use an external
metadata device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-integrity locks a range of sectors to prevent concurrent I/O or journal
writeback. These locks were not fair - so that many small overlapping I/Os
could starve a large I/O indefinitely.
Fix this by making the range locks fair. The ranges that are waiting are
added to the list "wait_list". If a new I/O overlaps some of the waiting
I/Os, it is not dispatched, but it is also added to that wait list.
Entries on the wait list are processed in first-in-first-out order, so
that an I/O can't starve indefinitely.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Decouple how dm_integrity_map_continue() responds to being out of free
sectors and when add_new_range() fails.
This has no functional change, but helps prepare for the next commit.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Early alpha processors can't write a byte or short atomically - they
read 8 bytes, modify the byte or two bytes in registers and write back
8 bytes.
The modification of the variable "suspending" may race with
modification of the variable "failed". Fix this by changing
"suspending" to an int.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add a new class for dm-delay that delays flush requests. Previously,
flushes were delayed as writes, but it caused problems if the user
needed to create a device with one or a few slow sectors for the purpose
of testing - all flushes would be forwarded to this device and delayed,
and that skews the test results. Fix this by allowing to select 0 delay
for flushes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-delay has a lot of code that is repeated for delaying read and write
bios. Repetitive code is generally bad; refactor out the repetitive
code in preperation for adding another delay class for flush bios.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More than one io_mode feature can be requested when creating a dm cache
device (as is: last one wins). The io_mode selections are incompatible
with one another, we should force them to be selected exclusively. Add
a counter to check for more than one io_mode selection.
Fixes: 629d0a8a1a ("dm cache metadata: add "metadata2" feature")
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Documentation/device-mapper-/thin-provisioning.txt's "Status" section no
longer reflected the current fitness level of DM thin-provisioning.
That is, DM thinp is no longer "EXPERIMENTAL". It has since seen
considerable improvement, has been fairly widely deployed and has
performed in a robust manner.
Update Documentation to dispel concern raised by potential DM thinp
users.
Reported-by: Drew Hastings <dhastings@crucialwebhost.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If T9.CTRL DISAMP is set, then pressure is reported as zero. This means
some app layers (eg tslib) will ignore the contact.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use sscanf to parse the configuration file, so it's necessary to zero
terminate the configuration otherwise a truncated file can cause the
parser to run off into uninitialised memory.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On devices with the T71 object, the config CRC will start there, rather
than at T7.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
aiptek_probe() is never called in atomic context. It calls
usb_alloc_coherent() with GFP_ATOMIC, which is not necessary. GFP_ATOMIC
can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
atp_open(), atp_recover() and atp_resume() are never called in atomic
context. They call usb_submit_urb() with GFP_ATOMIC, which is not
necessary. GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_probe() is never called in atomic context. It calls
usb_alloc_coherent() with GFP_ATOMIC, which is not necessary. GFP_ATOMIC
can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
powermate_alloc_buffers() is never called in atomic context. It calls
usb_alloc_coherent() with GFP_ATOMIC, which is not necessary. GFP_ATOMIC
can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
