There is no point in hiding this logic in a helper. Also remove the
useless events != 0 check and only busy loop once we know we actually
have a poll method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For any open socket file descriptor sock->sk->sk_wq->wait will always
point to sock->wq->wait. That means we can do the shorter dereference
and removal a NULL check and don't have to not worry about any RCU
protection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The metadata low watermark threshold is set by the kernel. But the
kernel depends on userspace to extend the thinpool metadata device when
the threshold is crossed.
Since the metadata low watermark threshold is not visible to userspace,
upon receiving an event, userspace cannot tell that the kernel wants the
metadata device extended, instead of some other eventing condition.
Making it visible (but not settable) enables userspace to affirmatively
know the kernel is asking for a metadata device extension, by comparing
metadata_low_watermark against nr_free_blocks_metadata, also reported in
status.
Current solutions like dmeventd have their own thresholds for extending
the data and metadata devices, and both devices are checked against
their thresholds on each event. This lessens the value of the kernel-set
threshold, since userspace will either extend the metadata device sooner,
when receiving another event; or will receive the metadata lowater event
and do nothing, if dmeventd's threshold is less than the kernel's.
(This second case is dangerous. The metadata lowater event will not be
re-sent, so no further event will be generated before the metadata
device is out if space, unless some other event causes userspace to
recheck its thresholds.)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
From the datasheet, the GPIO interface is identical to IT8728 (same
description), so just add it to the same case as the other chip.
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To cope with the changes in:
12c89130a5 ("x86/asm/memcpy_mcsafe: Add write-protection-fault handling")
60622d6822 ("x86/asm/memcpy_mcsafe: Return bytes remaining")
bd131544aa ("x86/asm/memcpy_mcsafe: Add labels for __memcpy_mcsafe() write fault handling")
da7bc9c57e ("x86/asm/memcpy_mcsafe: Remove loop unrolling")
This needed introducing a file with a copy of the mcsafe_handle_tail()
function, that is used in the new memcpy_64.S file, as well as a dummy
mcsafe_test.h header.
Testing it:
$ nm ~/bin/perf | grep mcsafe
0000000000484130 T mcsafe_handle_tail
0000000000484300 T __memcpy_mcsafe
$
$ perf bench mem memcpy
# Running 'mem/memcpy' benchmark:
# function 'default' (Default memcpy() provided by glibc)
# Copying 1MB bytes ...
44.389205 GB/sec
# function 'x86-64-unrolled' (unrolled memcpy() in arch/x86/lib/memcpy_64.S)
# Copying 1MB bytes ...
22.710756 GB/sec
# function 'x86-64-movsq' (movsq-based memcpy() in arch/x86/lib/memcpy_64.S)
# Copying 1MB bytes ...
42.459239 GB/sec
# function 'x86-64-movsb' (movsb-based memcpy() in arch/x86/lib/memcpy_64.S)
# Copying 1MB bytes ...
42.459239 GB/sec
$
This silences this perf tools build warning:
Warning: Kernel ABI header at 'tools/arch/x86/lib/memcpy_64.S' differs from latest version at 'arch/x86/lib/memcpy_64.S'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-igdpciheradk3gb3qqal52d0@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To get the changes in:
4c79579b44 ("bpf: Change bpf_fib_lookup to return lookup status")
That do not entail changes in tools/perf/ use of it, elliminating the
following perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/bpf.h' differs from latest version at 'include/uapi/linux/bpf.h'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-yei494y6b3mn6bjzz9g0ws12@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Even if the chip select line is not controlled by the SPFI
hardware, the device select bits need to be set to specify
the chip select line in use for the hardware to know what
parameters to use for the current transfer.
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's introduce an explicit check if skeys have already been enabled
for the vcpu, so we don't have to check the mm context if we don't have
the storage key facility.
This lets us check for enablement without having to take the mm
semaphore and thus speedup skey emulation.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We have a few places that already check if an inode has actual data in
the COW fork to avoid work on reflink inodes that do not actually have
outstanding COW blocks. There are a few more places that can avoid
working if doing the same check, so add a documented helper for this
condition and use it in all places where it makes sense.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We only have a few more callers left, so seize the opportunity and kill
it off.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Streamline the code and take advantage of the fact that kmem_realloc
through krealloc will be have like a normal allocation if passing in a
NULL old pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The field is only used for asserts, and to track if we really need to do
realloc when growing the inode fork data. But the krealloc function
already performs this check internally, so there is no need to keep track
of the real allocation size.
This will free space in the inode fork for keeping a sequence counter of
changes to the extent list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The new 'io_pgetevents' syscall was wired up in PowerPC in the following
cset:
b2f82565f2 ("powerpc: Wire up io_pgetevents")
Update tools/arch/powerpc/ copy of the asm/unistd.h file so that 'perf
trace' on PowerPC gets it in its syscall table.
This elliminated the following perf build warning:
Warning: Kernel ABI header at 'tools/arch/powerpc/include/uapi/asm/unistd.h' differs from latest version at 'arch/powerpc/include/uapi/asm/unistd.h'
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/n/tip-9uvu7tz4ud3bxxfyxwryuz47@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To get the changes in:
6cbc304f2f ("perf/x86/intel: Fix unwind errors from PEBS entries (mk-II)")
That do not imply any changes in the tooling side, the (ab)use of
sample_type is entirely done in kernel space, nothing for userspace to
witness here.
This cures the following warning during perf's build:
Warning: Kernel ABI header at 'tools/include/uapi/linux/perf_event.h' differs from latest version at 'include/uapi/linux/perf_event.h'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-o64mjoy35s9gd1gitunw1zg4@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Use 11M as tx rate for CCK protection control frames
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce mac80211 rts threshold handler in order to add frame
protection support to mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set MFP_CAPABLE bit in hw flag capabilities exported by the driver
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fall back to software encryption for hw unsupported ciphers in order
to enable 802.11w
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We find the memory use-after-free issue in __blk_drain_queue()
on the kernel 4.14. After read the latest kernel 4.18-rc6 we
think it has the same problem.
Memory is allocated for q->fq in the blk_init_allocated_queue().
If the elevator init function called with error return, it will
run into the fail case to free the q->fq.
Then the __blk_drain_queue() uses the same memory after the free
of the q->fq, it will lead to the unpredictable event.
The patch is to set q->fq as NULL in the fail case of
blk_init_allocated_queue().
Fixes: commit 7c94e1c157 ("block: introduce blk_flush_queue to drive flush machinery")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also moved the logic of the remapping to the nvme core driver instead
of implementing it in the nvme pci driver. This way all the other nvme
transport drivers will benefit from it (in case they'll implement metadata
support).
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently these functions are implemented in the scsi layer, but their
actual place should be the block layer since T10-PI is a general data
integrity feature that is used in the nvme protocol as well. Also, use
the tuple size from the integrity profile since it may vary between
integrity types.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently this function is implemented in the scsi layer, but it's
actual place should be the block layer since T10-PI is a general
data integrity feature that is used in the nvme protocol as well.
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need to check in blkcg_bio_issue_check if the bio is flagged as
QUEUE_ENTERED, because if it is then we've already accounted for the
size of the IO in the cgroup stats. We can still however account for
the extra IO since it'll be another request.
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While this ioctl is there at least since Kernel 2.6.12-rc2, it
was never used by any upstream driver.
Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the requirement for modern x86 system to enter lowest power mode
(SLP_S0) is SATA IP block to be off. This is true even during when
platform is suspended to idle and not only in opportunistic (runtime)
suspend.
Several of these system don't have traditional ACPI S3, so it is
important that they enter SLP_S0 state, to avoid draining battery even
during suspend. So it is important that out of the box Linux installation
reach this state.
SATA IP block doesn't get turned off till SATA is in DEVSLP mode. Here
user has to either use scsi-host sysfs or tools like powertop to set
the sata-host link_power_management_policy to min_power.
This change sets by default link power management policy to min_power
with partial (preferred) or slumber support on idle for some platforms.
To avoid regressions, the following conditions are used:
- User didn't override the policy from module parameter
- The kernel config is already set to use med_power_with_dipm or deeper
- System is a SLP_S0 capable using ACPI low power idle flag
This combination will make sure that systems are fairly recent and
since getting shipped with SLP_S0 support, the DEVSLP function
is already validated.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently when min_power policy is selected, the partial low power state
is not entered and link will try aggressively enter to only slumber state.
Add a new policy which still enable DEVSLP but also try to enter partial
low power state. This policy is presented as "min_power_with_partial".
For information the difference between partial and slumber
Partial – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ns.
Slumber – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ms.
Devslp – PHY logic is powered down. The link PM exit latency from this
state to active state maximum is 20 ms, unless otherwise specified by
DETO.
Suggested-and-reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The em28xx driver never touched the EM2874 register bits that control
the transport stream packet filters, leaving them at whatever default
the firmware has set. E.g. the Pinnacle 290e disables them by default,
while the Hauppauge WinTV dualHD enables discarding NULL packets by
default.
However, some applications require NULL packets, e.g. to determine the
load in DOCSIS segments, so discarding NULL packets is undesired for
such applications.
This patch simply extends the bit mask when starting or stopping the
transport stream packet capture, so that the filter bits are cleared.
It has been verified that this makes the Hauppauge WinTV dualHD pass
an unfiltered DVB-C stream including NULL packets, which it didn't
before.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kernel panic when with high memory pressure, calltrace looks like,
PID: 21439 TASK: ffff881be3afedd0 CPU: 16 COMMAND: "java"
#0 [ffff881ec7ed7630] machine_kexec at ffffffff81059beb
#1 [ffff881ec7ed7690] __crash_kexec at ffffffff81105942
#2 [ffff881ec7ed7760] crash_kexec at ffffffff81105a30
#3 [ffff881ec7ed7778] oops_end at ffffffff816902c8
#4 [ffff881ec7ed77a0] no_context at ffffffff8167ff46
#5 [ffff881ec7ed77f0] __bad_area_nosemaphore at ffffffff8167ffdc
#6 [ffff881ec7ed7838] __node_set at ffffffff81680300
#7 [ffff881ec7ed7860] __do_page_fault at ffffffff8169320f
#8 [ffff881ec7ed78c0] do_page_fault at ffffffff816932b5
#9 [ffff881ec7ed78f0] page_fault at ffffffff8168f4c8
[exception RIP: _raw_spin_lock_irqsave+47]
RIP: ffffffff8168edef RSP: ffff881ec7ed79a8 RFLAGS: 00010046
RAX: 0000000000000246 RBX: ffffea0019740d00 RCX: ffff881ec7ed7fd8
RDX: 0000000000020000 RSI: 0000000000000016 RDI: 0000000000000008
RBP: ffff881ec7ed79a8 R8: 0000000000000246 R9: 000000000001a098
R10: ffff88107ffda000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000008 R14: ffff881ec7ed7a80 R15: ffff881be3afedd0
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
It happens in the pagefault and results in double pagefault
during compacting pages when memory allocation fails.
Analysed the vmcore, the page leads to second pagefault is corrupted
with _mapcount=-256, but private=0.
It's caused by the race between migration and ballooning, and lock
missing in virtballoon_migratepage() of virtio_balloon driver.
This patch fix the bug.
Fixes: e22504296d ("virtio_balloon: introduce migration primitives to balloon pages")
Cc: stable@vger.kernel.org
Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Huang Chong <huang.chong@zte.com.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Implement 802.11ax D2.0;
* Changes in the base code to support the new 22560 devices;
* Support for the new 22560 device family;
-----BEGIN PGP SIGNATURE-----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=M2sG
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi patches for 4.19
* Implement 802.11ax D2.0;
* Changes in the base code to support the new 22560 devices;
* Support for the new 22560 device family;
commit 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver") did not add the configuration and build infrastructure to
configure and build the mobiveil controller driver, so at present the
driver code is in the kernel but cannot be compiled.
Add the mobiveil controller driver Kconfig/Makefile infrastructure.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
PCI mobiveil host controller driver currently fails to compile
with the following error:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_probe':
drivers/pci/controller/pcie-mobiveil.c:788:8: error: implicit
declaration of function 'devm_of_pci_get_host_bridge_resources'; did you
mean 'pci_get_host_bridge_device'?
[-Werror=implicit-function-declaration]
ret = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pci_get_host_bridge_device
Add the missing include file to pull in the required function declaration.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The field pcie_reg_base in struct mobiveil_pcie represents a physical
address so it should be of phys_addr_t type rather than void __iomem*;
this results in the following compilation warnings:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_parse_dt':
drivers/pci/controller/pcie-mobiveil.c:326:22: warning: assignment makes
pointer from integer without a cast [-Wint-conversion]
pcie->pcie_reg_base = res->start;
^
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_enable_msi':
drivers/pci/controller/pcie-mobiveil.c:485:25: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t msg_addr = pcie->pcie_reg_base;
^~~~
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_compose_msi_msg':
drivers/pci/controller/pcie-mobiveil.c:640:21: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t addr = pcie->pcie_reg_base + (data->hwirq * sizeof(int));
Fix the type and with it the compilation warnings.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MFD part for bd71837 was changed during the review. Clean regulator part to
match changed MFD:
- renamed header file => fix include
- remove unused platdata as also type definition was removed
- Kconfig option for MFD part was changed => fix depends on clause
- Rename Kconfig option for regulators
As Kconfig option for regulators gets now used (when dependency to MFD is
satisfied) change it so that it won't require new change when support for
bd71847 is added.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.
Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tegra SDHCI controllers require the SDHCI clock divider to be configured
to divide the clock by two in DDR50/52 modes. Incorrectly configured
clock divider results in corrupted data.
Prevent the possibility of incorrectly calculating the divider value due
to clock rate rounding or low parent clock frequency by not assigning
host->max_clk to clk_get_rate() on tegra_sdhci_set_clock().
See the comments for further details.
Fixes: a8e326a ("mmc: tegra: implement module external clock change")
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The trigger flag in vmidi object can be referred in different contexts
concurrently, hence it's better to be put with READ_ONCE() and
WRITE_ONCE() macros to assure the accesses.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The virmidi sequencer stuff tries to translate the rawmidi bytes to
sequencer events and deliver the packets at trigger callback. The
amount of the whole process of these translations and deliveries
depends on the incoming rawmidi bytes, and we have no limit for that;
this was the cause of a CPU soft lockup that had been reported and
fixed recently.
Although we've fixed the soft lockup by putting the temporary unlock
and cond_resched(), it's rather a quick band aid. In this patch,
meanwhile, the event parsing and delivery process is offloaded to a
dedicated work, and the trigger callback just kicks it off. It has
three merits, at least:
- The processing is always done in a sleepable context, which can
assure the event delivery with non-atomic flag without hackish
is_atomic() usage.
- Other relevant codes can be simplified, reducing the lines
- It makes me happier
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Found and reported by kbuild test robot:
Message ID: <201805052003.MC007f9h%fengguang.wu@intel.com>
and holding an address of an empty struct in .driver.pm does no harm
when CONFIG_PM_SLEEP is not defined.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dvb-pll module was 'put' twice on exit:
once by dvb_frontend_detach() and another by dvb_module_release().
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Friio device contains "gl861" bridge and "tc90522" demod,
for which the separate drivers are already in the kernel.
But friio driver was monolithic and did not use them,
practically copying those features.
This patch decomposes friio driver into sub drivers and
re-uses existing ones, thus reduces some code.
It adds some features to gl861,
to support the friio-specific init/config of the devices
and implement i2c communications to the tuner via demod
with USB vendor requests.
[mchehab+samsung@kernel.org: fix merge conflicts]
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds bindings for Snapdragon 845 display processing unit
Changes in v2:
- Use SoC specific compatibles for mdss and dpu (Rob Herring)
- Use assigned-clocks to set initial clock frequency (Rob Herring)
Changes in v3 (all suggested by Rob Herring):
- Rename mdss_phys to mdss
- Correct description for clocks/assigned-clocks
- Rename mdp_phys to mdp
- Rename vbif_phys to vbif
- Remove redundant interrupt-parent from mdss_mdp
- Fully specify 'ranges' and use relative reg address in mdss_mdp
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Adds mdp transfer time to msm dsi binding
Changes in v3:
- Added Rob's R-b
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Mark a number of static functions that are only unsed in the file
that defines them and remove the prototypes from the headers where
needed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove dpu_format_get_block_size, dpu_format_get_framebuffer_size,
dpu_set_scaler_v2 and dpu_copy_formats they are unused and unneeded.
Signed-off-by: Jordan Crouse <jcrouse@codeauorora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
