Since we are waiting on all ordered extents at the start of the fsync()
path we don't need to wait on any logged ordered extents, and we don't
need to look up the checksums on the ordered extents as they will
already be on disk prior to getting here. Rework this so we're only
looking up and copying the on-disk checksums for the extent range we
care about.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There's a priority inversion that exists currently with btrfs fsync. In
some cases we will collect outstanding ordered extents onto a list and
only wait on them at the very last second. However this "very last
second" falls inside of a transaction handle, so if we are in a lower
priority cgroup we can end up holding the transaction open for longer
than needed, so if a high priority cgroup is also trying to fsync()
it'll see latency.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The comment wrongfully states that the owner parameter is the level of
the parent block. In fact owner is the level of the current block and
by adding 1 to it we can eventually get to the parent/root.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Here is a doc-only patch which tires to deobfuscate the terra-incognita
that arguments for delayed refs are.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit ac0b4145d6 ("btrfs: scrub: Don't use inode pages
for device replace") the function is not used and we can remove all
functions down the call chain.
There was an optimization that reused inode pages to speed up device
replace, but broke when there was nodatasum and compressed page. The
potential performance gain is small so we don't loose much by removing
it and using scrub_pages same as the other pages.
Signed-off-by: Qu Wenruo <wqu@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
The get_seconds() function is deprecated as it truncates the timestamp
to 32 bits. Change it to or ktime_get_real_seconds().
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
This GPIO controller can serve as an interrupt controller as well on the
GPIOs it handles.
An interrupt is generated whenever a GPIO line changes and the
interrupt for this GPIO line is enabled. This means that both the
changes from low to high and high to low generate an interrupt.
For some use cases, it makes sense to ignore the high to low change and
not generate an interrupt. Such a use case is a line that is hold in a
level high/low manner until the event holding the line gets acked.
This can be achieved by making sure the interrupt on the GPIO controller
side gets acked and masked only after the line gets hold in its default
state, this is what's done with the fasteoi functions.
Only IRQ_TYPE_EDGE_BOTH and IRQ_TYPE_LEVEL_HIGH are supported for now.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- GICv3 ITS LPI allocation revamp
- GICv3 support for hypervisor-enforced LPI range
- GICv3 ITS conversion to raw spinlock
-----BEGIN PGP SIGNATURE-----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=gKw8
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- GICv3 ITS LPI allocation revamp
- GICv3 support for hypervisor-enforced LPI range
- GICv3 ITS conversion to raw spinlock
There isn't a hard dependency of the Xilinx AXI-PCIe host bridge on any
architecture. For example: at SiFive we map RISC-V cores to Xilinx FPGAs
and connect the Xilinx IP via a TileLink adapter, so the RISC-V Linux
port will need to be able to enable PCIE_XILINX in order to have PCIe
support.
This patch decouples the PCIE_XILINX support from ARCH. Instead it just
depends on OF, which is the only true dependency.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
[hch: switch to OF instead of OF_PCI now that the latter is gone]
Signed-off-by: Christoph Hellwig <hch@lst.de>
[lorenzo.pieralisi@arm.com: trimmed the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
At present, "systemctl suspend" and "shutdown" can run in parrallel. A
system can suspend after devices_shutdown(), and resume. Then the shutdown
task goes on to power off. This causes many devices are not really shut
off. Hence replacing reboot_mutex with system_transition_mutex (renamed
from pm_mutex) to achieve the exclusion. The renaming of pm_mutex as
system_transition_mutex can be better to reflect the purpose of the mutex.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ath.git patches for 4.19. Major changes:
ath10k
* add debugfs file warm_hw_reset
wil6210
* add debugfs files tx_latency, link_stats and link_stats_global
* add 3-MSI support
* allow scan on AP interface
* support max aggregation window size 64
Since mac802154_hwsim the fakelb driver will get deprecated. This patch will
notifier all users of fakelb to switch to the new mac802154_hwsim driver.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch adds a new virtual driver mac802154_hwsim which is based on
the fakelb driver.
The fakelb driver will get deprecated and hopefully removed someday.
The main reason for doing this step is to rename the driver to
mac802154_hwsim to have a similar naming scheme as mac80211_hwsim,
which is more popular in the 802.11 wireless word and the idea is the
same behind this driver.
The new features of this driver are to have knowledge about connected
edges, which can be changed during runtime. This offers a testing
environment for routing protocols e.g. RPL.
The default behaviour is still as fakelb: two radios connected to each
other. New added radios during runtime will not be connected to other
wpan_hwsim instances.
The netlink api is not namespace aware on purpose, only the registered
wpan_phy's can be moved to namespaces. The physical layer according to
wiresless "air" communication can be handled across namespaces.
Furthermore the edges can be weighted with the LQI value according IEEE
802.15.4 which offers additional handling to mark bad or good connection
indicators to other connected virtual phys.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Pointers fq and net are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'fq' set but not used [-Wunused-but-set-variable]
warning: variable 'net' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch is necessary if case of AF_PACKET or other socket interface
which I am aware of it and didn't allocated the necessary room.
Reported-by: David Palma <david.palma@ntnu.no>
Reported-by: Rabi Narayan Sahoo <rabinarayans0828@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch fixes patch add handling to take care tail and headroom for
single 6lowpan frames. We need to be sure we have a skb with the right
head and tailroom for single frames. This patch do it by using
skb_copy_expand() if head and tailroom is not enough allocated by upper
layer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195059
Reported-by: David Palma <david.palma@ntnu.no>
Reported-by: Rabi Narayan Sahoo <rabinarayans0828@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This addresses Coverity-ID: 114713 ("Missing break in switch").
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If we get a keyed wakeup for a aio poll waitqueue and wake can acquire the
ctx_lock without spinning we can just complete the iocb straight from the
wakeup callback to avoid a context switch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Avi Kivity <avi@scylladb.com>
Simple one-shot poll through the io_submit() interface. To poll for
a file descriptor the application should submit an iocb of type
IOCB_CMD_POLL. It will poll the fd for the events specified in the
the first 32 bits of the aio_buf field of the iocb.
Unlike poll or epoll without EPOLLONESHOT this interface always works
in one shot mode, that is once the iocb is completed, it will have to be
resubmitted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Avi Kivity <avi@scylladb.com>
This is needed to prevent races caused by the way the ->poll API works.
To avoid introducing overhead for other users of the iocbs we initialize
it to zero and only do refcount operations if it is non-zero in the
completion path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Avi Kivity <avi@scylladb.com>
When HWP is active turbo active ratio is not used, so we should allow
policy max frequency above turbo activation ratio to be set. When HWP is
not active, then any policy max frequency above turbo activation ratio
can result upto max one-core turbo frequency.
This fix helps better thermal control in turbo region when other methods
like "Running Average Power Limit" is not available to use.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The its_lock lock is held while a new device is added to the list and
during setup while the CPU is booted. Even on -RT the CPU-bootup is
performed with disabled interrupts.
Make its_lock a raw_spin_lock_t.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Like on X1C6, on X1Y3 EC interrupts constantly wake up system from
s2idle, the power consumption is extremely high.
So make ec_no_wakeup be true as default to keep system in s2idle mode
and reduce power consumption.
Power button works when ec_no_wakeup=true.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A commit 28b208f600 ('ALSA: dice: add parameters of stream formats for
models produced by Alesis') adds wrong copy to rx parameters instead of
tx parameters for Alesis iO26.
This commit fixes the bug for v4.18-rc8.
Fixes: 28b208f600 ('ALSA: dice: add parameters of stream formats for models produced by Alesis')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v4.18
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115156 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comment with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the tools/lib/bpf/btf.[ch] to LGPL which
is inline with libbpf also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The chardev conversion forgot to copy the fsi_dev,
silly mistake, compounded by a testing mistake on
my side, this specific driver wasn't being tested
properly.
Fixes: d8f4587655 "fsi: scom: Convert to use the new chardev"
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A minor version number increase should not break backwards
compatibility.
Fixes: 3cb98f84d3 ("lightnvm: add minor version to generic geometry")
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe changes from Christoph:
"This contains the support for TP4004, Asymmetric Namespace Access,
which makes NVMe multipathing usable in practice."
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvmet: use Retain Async Event bit to clear AEN
nvmet: support configuring ANA groups
nvmet: add minimal ANA support
nvmet: track and limit the number of namespaces per subsystem
nvmet: keep a port pointer in nvmet_ctrl
nvme: add ANA support
nvme: remove nvme_req_needs_failover
nvme: simplify the API for getting log pages
nvme.h: add ANA definitions
nvme.h: add support for the log specific field
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into for-4.19/block2
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a
merge conflict down the line.
Signed-of-by: Jens Axboe <axboe@kernel.dk>
Match patterns for some skbedit tests contain duplicate whitespace that is
not present in actual tc output. This causes tests to fail because they
can't match required action, even when it was successfully created.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match patterns for some connmark tests contain duplicate whitespace that is
not present in actual tc output. This causes tests to fail because they
can't match required action, even when it was successfully created.
Fixes: 1dad0f9fff ("tc-testing: add connmark action tests")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test 6fb4 creates one mirred and one pipe action, but only flushes mirred
on teardown. Leaking pipe action causes failures in other tests.
Add additional teardown command to also flush gact actions.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix expected ip address to actually match configured ip address.
Fix test to expect single matched filter.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbZyxDAAoJEG4XJFUm622bq2AH/2yJAeOKb7Z25ezsvldaEDd3
cYS4TjLevXacDU5NdINtm1IRMct1ZldwUjrjgR2I/eLaSHhxyIdV4hb05etSN8qZ
yo86aa1gs+8rSEn/GVO8UjX8Bh4NM/tff+yzMKWiWJGe9DtBvswSUPxBOU91vS8K
WcCpvWh9SpmAPyZEDWsZnTK7AUc+X2T+Soit+pJmLm9P3RxkvMqQxG82eMGVnooO
5aNe0T9zYLB4aB8unCJqPSYSLVDJ55vnC8tFIjcEhNCF/745gyMD/CrcQ4zCxdN/
KF6WEDc/XePF5qrHvkzWA7HiR0Xs9pDt3KugkU0enZV+cba0kKaBq230sZ++1KM=
=BwxN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC791, 68 bytes is the minimum size of IPv4 datagram every
device must be able to forward without further fragmentation while 576
bytes is the minimum size of IPv4 datagram every device has to be able
to receive, so in ip6_tnl_xmit(), 68(IPV4_MIN_MTU) should be the right
value for the ipv4 min mtu check in ip6_tnl_xmit.
While at it, change to use max() instead of if statement.
Fixes: c9fefa0819 ("ip6_tunnel: get the min mtu properly in ip6_tnl_xmit")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-08-05
Here's the main bluetooth-next pull request for the 4.19 kernel.
- Added support for Bluetooth Advertising Extensions
- Added vendor driver support to hci_h5 HCI driver
- Added serdev support to hci_h5 driver
- Added support for Qualcomm wcn3990 controller
- Added support for RTL8723BS and RTL8723DS controllers
- btusb: Added new ID for Realtek 8723DE
- Several other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Enable MC-aware mode for mlxsw ports
Petr says:
Due to an issue in Spectrum chips, when unicast traffic shares the same
queue as BUM traffic, and there is a congestion, the BUM traffic is
admitted to the queue anyway, thus pushing out all UC traffic. In order
to give unicast traffic precedence over BUM traffic, configure
multicast-aware mode on all ports.
Under multicast-aware regime, when assigning traffic class to a packet,
the switch doesn't merely take the value prescribed by the QTCT
register. For BUM traffic, it instead assigns that value plus 8. That
limits the number of available TCs, but since mlxsw currently only uses
the lower eight anyway, it is no real loss.
The two TCs (UC and MC one) are then mapped to the same subgroup and
strictly prioritized so that UC traffic is preferred in case of
congestion.
In patch #1, introduce a new register, QTCTM, which enables the
multicast-aware mode.
In patch #2, fix a typo in related code.
In patch #3, set up TCs and QTCTM to enable multicast-aware mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to give unicast traffic precedence over BUM traffic, configure
multicast-aware mode on all ports.
Under multicast-aware regime, when assigning traffic class to a packet,
the switch doesn't merely take the value prescribed by the QTCT
register. For BUM traffic, it instead assigns that value plus 8.
ETS elements for TCs 8..15 thus need to be configured as well. Extend
mlxsw_sp_port_ets_init() so that it maps each of them to the same
subgroup as their corresponding TC from the range 0..7, such that TCs X
and X+8 map to the same subgroup.
The existing code configures TCs with strict priority. So far this was
immaterial, because each TC had its own subgroup. Now that two TCs share
a subgroup it becomes important. TCs are prioritized in order of 7, 6,
..., 0, 15, 14, ..., 8: the higher TCs used for BUM traffic end up being
deprioritized. Since that's what's needed, keep that configuration as it
is, and configure the new TCs likewise.
Finally in mlxsw_sp_port_create(), invoke configuration of QTCTM to
enable MC-aware mode on each port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures if the Switch Priority to Traffic Class mapping
is based on Multicast packet indication. If so, then multicast packets
will get a Traffic Class that is plus (cap_max_tclass_data/2) the value
configured by QTCT.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1402059 ("Missing break in switch")
Addresses-Coverity-ID: 1402060 ("Missing break in switch")
Addresses-Coverity-ID: 1402061 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to set the error code on this path, so we return NULL instead
of an error pointer. In the current code kzalloc() won't fail for small
allocations so this doesn't really affect runtime.
Fixes: b95ec7eb3b ("net: sched: cls_flower: implement chain templates")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_set_mtu_ext is able to fail with a valid mtu value, at that
condition, extack._msg is not set and random since it is in stack,
then kernel will crash when print it.
Fixes: 7a4c53bee3 ("net: report invalid mtu value via netlink extack")
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
