Allocations larger than PAGE_ALLOC_COSTLY_ORDER are unreliable and they
may fail anytime. This patch fixes the udlfb driver so that when a large
alloactions fails, it tries to do multiple smaller allocations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The default delay 5 jiffies is too much when the kernel is compiled with
HZ=100 - it results in jumpy cursor in Xwindow.
In order to find out the optimal delay, I benchmarked the driver on
1280x720x30fps video. I found out that with HZ=1000, 10ms is acceptable,
but with HZ=250 or HZ=300, we need 4ms, so that the video is played
without any frame skips.
This patch changes the delay to this value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The defio subsystem overwrites the method fb_osp->mmap. That method is
stored in module's static data - and that means that if we have multiple
diplaylink adapters, they will over write each other's method.
In order to avoid interference between multiple adapters, we copy the
fb_ops structure to a device-local memory.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The udlfb driver reprograms the hardware everytime the user switches the
console, that makes quite unusable when working on the console.
This patch makes the driver remember the videomode we are in and avoid
reprogramming the hardware if we switch to the same videomode.
We mask the "activate" field and the "FB_VMODE_SMOOTH_XPAN" flag when
comparing the videomode, because they cause spurious switches when
switching to and from the Xserver.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The displaylink hardware has such a peculiarity that it doesn't render a
command until next command is received. This produces occasional
corruption, such as when setting 22x11 font on the console, only the first
line of the cursor will be blinking if the cursor is located at some
specific columns.
When we end up with a repeating pixel, the driver has a bug that it leaves
one uninitialized byte after the command (and this byte is enough to flush
the command and render it - thus it fixes the screen corruption), however
whe we end up with a non-repeating pixel, there is no byte appended and
this results in temporary screen corruption.
This patch fixes the screen corruption by always appending a byte 0xAF at
the end of URB. It also removes the uninitialized byte.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
I observed that the performance of the udl fb driver degrades over time.
On a freshly booted machine, it takes 6 seconds to do "ls -la /usr/bin";
after some time of use, the same operation takes 14 seconds.
The reason is that the value of "limit_sem" decays over time.
The udl driver uses a semaphore "limit_set" to specify how many free urbs
are there on dlfb->urbs.list. If the count is zero, the "down" operation
will sleep until some urbs are added to the freelist.
In order to avoid some hypothetical deadlock, the driver will not call
"up" immediately, but it will offload it to a workqueue. The problem is
that if we call "schedule_delayed_work" on the same work item multiple
times, the work item may only be executed once.
This is happening:
* some urb completes
* dlfb_urb_completion adds it to the free list
* dlfb_urb_completion calls schedule_delayed_work to schedule the function
dlfb_release_urb_work to increase the semaphore count
* as the urb is on the free list, some other task grabs it and submits it
* the submitted urb completes, dlfb_urb_completion is called again
* dlfb_urb_completion calls schedule_delayed_work, but the work is already
scheduled, so it does nothing
* finally, dlfb_release_urb_work is called, it increases the semaphore
count by 1, although it should increase it by 2
So, the semaphore count is decreasing over time, and this causes gradual
performance degradation.
Note that in the current kernel, the "up" function may be called from
interrupt and it may race with the "down" function called by another
thread, so we don't have to offload the call of "up" to a workqueue at
all. This patch removes the workqueue code. The patch also changes
"down_interruptible" to "down" in dlfb_free_urb_list, so that we will
clean up the driver properly even if a signal arrives.
With this patch, the performance of udlfb no longer degrades.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
[b.zolnierkie: fix immediatelly -> immediately typo]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
I have a USB display adapter using the udlfb driver and I use it on an ARM
board that doesn't have any graphics card. When I plug the adapter in, the
console is properly displayed, however when I unplug and re-plug the
adapter, the console is not displayed and I can't access it until I reboot
the board.
The reason is this:
When the adapter is unplugged, dlfb_usb_disconnect calls
unlink_framebuffer, then it waits until the reference count drops to zero
and then it deallocates the framebuffer. However, the console that is
attached to the framebuffer device keeps the reference count non-zero, so
the framebuffer device is never destroyed. When the USB adapter is plugged
again, it creates a new device /dev/fb1 and the console is not attached to
it.
This patch fixes the bug by unbinding the console from unlink_framebuffer.
The code to unbind the console is moved from do_unregister_framebuffer to
a function unbind_console. When the console is unbound, the reference
count drops to zero and the udlfb driver frees the framebuffer. When the
adapter is plugged back, a new framebuffer is created and the console is
attached to it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Bernie Thompson <bernie@plugable.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: stable@vger.kernel.org
[b.zolnierkie: preserve old behavior for do_unregister_framebuffer()]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Alter the state-check assertion in fscache_enqueue_operation() to allow
cancelled operations to be given processing time so they can be cleaned up.
Also fix a debugging statement that was requiring such operations to have
an object assigned.
Fixes: 9ae326a690 ("CacheFiles: A cache that backs onto a mounted filesystem")
Reported-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
It doesn't make sense to set the PIE frequency from the driver. Let
userspace do its job.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This is implementing multi-stream decoder support. The multi-stream
will be used to enable/disable the primary/secondary decoder
outputs. Depending on formats on both decoder outputs we could
implement downscale, dithering and supporting UBWC (universal
bandwidth compression) formats. The UBWC compressed raw format is
used to optimize interconnect bandwidth for bigger resolutions
like 4K and hence we will get some power-saving benefits as well.
Both decoder outputs are distinguished by buffer_type field in
the HFI packets. For example HFI_BUFFER_OUTPUT is the buffer type
for primary decoder output and HFI_BUFFER_OUTPUT2 is for secondary
decoder output.
Starting from Venus 4xx the DPB buffers format must be UBWC, so
the multi-stream becomes mandatory for this Venus version. That
means that we need to allocate internally in the driver a set of
DPB buffers (with UBWC NV12 format) and give them to the firmware.
The other decoder output (we called it OPB) format will be NV12
linear format and with the same resolution (or smaller in case
the user wants to downscale).
The DPB buffers are used for decoder reference frames and those
have to be in a specific format (UBWC). So one decoder output is
used to fill those reference buffers while the other output is
used to fill the userspace buffers with the user requested format.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This move the calculations of raw and compressed buffer sizes
on common helper and make it identical for encoder and decoder.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make a new function vdec_output_conf() for decoder output
configuration. vdec_output_conf() will set properties via
HFI interface related to the output configuration, and
keep vdec_set_properties() which will set properties
related to decoding parameters.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework and rename vdec_cap_num_buffers() to get the number of
input buffers too.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend venus_helper_set_num_bufs() helper function with one more
argument to set number of output buffers for the secondary decoder
output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These are new properties applicable to Venus version 4xx. Add the
helpers and call them from decoder and encoder drivers.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The new helper will has one more argument for buffer type, that
way the decoder can configure the format on it's secondary
output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds one more function argument to pass buffer type to
set_output_resolution() helper function. That is a preparation
to support secondary decoder output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Delete not used flag for capture buffer allocation mode and
no longer used cap_bufs_mode_dynamic from instance structure.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add and use a helper function to set actual buffer size for
particular buffer type. This is also preparation to use
the second decoder output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds a new helper function to set dynamic buffer mode if it is
supported by current HFI version. The dynamic buffer mode is
set unconditionally for both decoder outputs.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename is_reg_unreg_needed() to better name is_dynamic_bufmode() and
use buffer mode from enumerated per codec capabilities.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds common capability parser for all supported Venus
versions. Having it will help to enumerate better the supported
raw formats and codecs and also the capabilities for every
codec like max/min width/height, framerate, bitrate and so on.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add two more clocks for Venus 4xx in core structure and create
a new power enable function to handle it for 3xx/4xx versions.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds suspend (power collapse) functionality by reusing
the suspend function for Venus 3xx and also enables idle indicator
property for Venus 4xx (where it is disabled by default).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This moves setting of default properties (firmware debug, idle
indicator and low power mode) from session init to core init.
All of those properties are need to be enabled/disabled early
so that they could be used before the clients are even initialized.
The other reason is to set idle indicator property early before
we enter into venus_suspend function where we need to check for
ARM9 WFI.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This fixes the suspend function for Venus 3xx versions by
add a check for WFI (wait for interrupt) bit. This bit
is on when the ARM9 is idle and entered in low power mode.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add AXI halt support for version 4xx by using venus wrapper
registers.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds handling of buffers of type OUTPUT2 which is needed to
support Venus 4xx version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This makes possible to handle session_continue for 4xx as well.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
HFI version 4xx can pass more properties in the sequence change
event, extend the event structure with them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Data pointer should be incremented by size of the structure not
the size of a pointer, correct the mistake.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an entry to make myself a maintainer of STM32 DCMI media driver.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. kinect_read returns the result of
usb_control_msg, which can return a negtive error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error path currently calls tw686x_video_free() which requires
vc->dev to be initialized, causing a NULL dereference on uninitizalized
channels.
Fix this by setting the vc->dev fields for all the channels first.
Fixes: f8afaa8dbc ("[media] tw686x: Introduce an interface to support multiple DMA modes")
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are no DMA devices registered yet, return with EPROBE_DEFER
similarly to the case when requesting a slave channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AMG88xx has an on-board thermistor which is used for more accurate
processing of its temperature readings from the 8x8 thermopile array
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Arnd reports the following arm64 randconfig build error with the PSI
patches that add another page flag:
/git/arm-soc/arch/arm64/mm/init.c: In function 'mem_init':
/git/arm-soc/include/linux/compiler.h:357:38: error: call to
'__compiletime_assert_618' declared with attribute error: BUILD_BUG_ON
failed: sizeof(struct page) > (1 << STRUCT_PAGE_MAX_SHIFT)
The additional page flag causes other information stored in
page->flags to get bumped into their own struct page member:
#if SECTIONS_WIDTH+ZONES_WIDTH+NODES_SHIFT+LAST_CPUPID_SHIFT <=
BITS_PER_LONG - NR_PAGEFLAGS
#define LAST_CPUPID_WIDTH LAST_CPUPID_SHIFT
#else
#define LAST_CPUPID_WIDTH 0
#endif
#if defined(CONFIG_NUMA_BALANCING) && LAST_CPUPID_WIDTH == 0
#define LAST_CPUPID_NOT_IN_PAGE_FLAGS
#endif
which in turn causes the struct page size to exceed the size set in
STRUCT_PAGE_MAX_SHIFT. This value is an an estimate used to size the
VMEMMAP page array according to address space and struct page size.
However, the check is performed - and triggers here - on a !VMEMMAP
config, which consumes an additional 22 page bits for the sparse
section id. When VMEMMAP is enabled, those bits are returned, cpupid
doesn't need its own member, and the page passes the VMEMMAP check.
Restrict that check to the situation it was meant to check: that we
are sizing the VMEMMAP page array correctly.
Says Arnd:
Further experiments show that the build error already existed before,
but was only triggered with larger values of CONFIG_NR_CPU and/or
CONFIG_NODES_SHIFT that might be used in actual configurations but
not in randconfig builds.
With longer CPU and node masks, I could recreate the problem with
kernels as old as linux-4.7 when arm64 NUMA support got added.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms.")
Fixes: 3e1907d5bf ("arm64: mm: move vmemmap region right below the linear region")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This enables reordering support for h.264 main profile level 4.2,
5.0, and 5.1 streams. Even though we likely can't play back such
streams at full speed, we should still recognize them correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allow to set a crop rectangle on the encoder output queue to set the
visible resolution as required by the V4L2 codec API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit d3aec8a28b ("arm64: capabilities: Restrict KPTI
detection to boot-time CPUs") we rely on errata flags being already
populated during feature enumeration. The order of errata and
features was flipped as part of commit ed478b3f9e ("arm64:
capabilities: Group handling of features and errata workarounds").
Return to the orginal order of errata and feature evaluation to
ensure errata flags are present during feature evaluation.
Fixes: ed478b3f9e ("arm64: capabilities: Group handling of
features and errata workarounds")
CC: Suzuki K Poulose <suzuki.poulose@arm.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In pl330_update() when checking if a channel has been aborted, the
channel's lock is not taken, only the overall pl330_dmac lock. But in
pl330_terminate_all() the aborted flag (req_running==-1) is set under
the channel lock and not the pl330_dmac lock.
With threaded interrupts, this leads to a potential race:
pl330_terminate_all pl330_update
------------------- ------------
lock channel
entry
lock pl330
_stop channel
unlock pl330
lock pl330
check req_running != -1
req_running = -1
_start channel
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove the intermediate width and height variables, the calculation is
simple enough.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All internal YCbCr frame buffers are the same size, calculate ycbcr_size
once before the allocation loop.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
