From 0ec4ee3c9b9755b28fd2e89b2ceaae6f15403368 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:10 +0530
Subject: [PATCH 01/28] mmc: sdhci-omap: Fix when capabilities are obtained
 from SDHCI_CAPABILITIES reg

sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index 1456abd5eeb9..e7e43f2ae224 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -916,10 +916,6 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 		goto err_put_sync;
 	}
 
-	ret = sdhci_omap_config_iodelay_pinctrl_state(omap_host);
-	if (ret)
-		goto err_put_sync;
-
 	host->mmc_host_ops.get_ro = mmc_gpio_get_ro;
 	host->mmc_host_ops.start_signal_voltage_switch =
 					sdhci_omap_start_signal_voltage_switch;
@@ -930,12 +926,23 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	sdhci_read_caps(host);
 	host->caps |= SDHCI_CAN_DO_ADMA2;
 
-	ret = sdhci_add_host(host);
+	ret = sdhci_setup_host(host);
 	if (ret)
 		goto err_put_sync;
 
+	ret = sdhci_omap_config_iodelay_pinctrl_state(omap_host);
+	if (ret)
+		goto err_cleanup_host;
+
+	ret = __sdhci_add_host(host);
+	if (ret)
+		goto err_cleanup_host;
+
 	return 0;
 
+err_cleanup_host:
+	sdhci_cleanup_host(host);
+
 err_put_sync:
 	pm_runtime_put_sync(dev);
 

From 5bc2bda54d49cb2dbf9387b47feb25c32d20e216 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:11 +0530
Subject: [PATCH 02/28] mmc: sdhci-omap: Remove setting ADMA capability in
 driver

sdhci can directly get ADMA capability from MMCHS_CAPA register.
Remove explicitly setting ADMA here as some instances might not have
ADMA enabled. (sdhci_read_caps() is also removed from here since
sdhci_setup_host() invokes it).

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index e7e43f2ae224..78f3ceea570e 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -923,9 +923,6 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	host->mmc_host_ops.card_busy = sdhci_omap_card_busy;
 	host->mmc_host_ops.execute_tuning = sdhci_omap_execute_tuning;
 
-	sdhci_read_caps(host);
-	host->caps |= SDHCI_CAN_DO_ADMA2;
-
 	ret = sdhci_setup_host(host);
 	if (ret)
 		goto err_put_sync;

From 212f4f8a44909a5f2db187b2ff7cfba46c626528 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:12 +0530
Subject: [PATCH 03/28] mmc: sdhci-omap: Workaround for Errata i843
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Errata i843 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
PG 1.0/1.1 silicon has limitations w.r.t frequencies at which MMC1/2/3
can operate.

Use soc_device_match() to identify rev 1.0/1.1 silicon and
override mmc->f_max according to the errata workaround.
"max-frequency" dt property cannot be used since the device
tree is added for rev 2.0 silicon.

soc_device_match() is also used in order to get the IODelay values
for rev 1.0/1.1 silicon.

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 35 ++++++++++++++++++++++++++++++++++-
 1 file changed, 34 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index 78f3ceea570e..b3dc7f1466e5 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -26,6 +26,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/sys_soc.h>
 
 #include "sdhci-pltfm.h"
 
@@ -100,6 +101,7 @@ struct sdhci_omap_data {
 };
 
 struct sdhci_omap_host {
+	char			*version;
 	void __iomem		*base;
 	struct device		*dev;
 	struct	regulator	*pbias;
@@ -733,12 +735,21 @@ static struct pinctrl_state
 				  u32 *caps, u32 capmask)
 {
 	struct device *dev = omap_host->dev;
+	char *version = omap_host->version;
 	struct pinctrl_state *pinctrl_state = ERR_PTR(-ENODEV);
+	char str[20];
 
 	if (!(*caps & capmask))
 		goto ret;
 
-	pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, mode);
+	if (version) {
+		snprintf(str, 20, "%s-%s", mode, version);
+		pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, str);
+	}
+
+	if (IS_ERR(pinctrl_state))
+		pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, mode);
+
 	if (IS_ERR(pinctrl_state)) {
 		dev_err(dev, "no pinctrl state for %s mode", mode);
 		*caps &= ~capmask;
@@ -830,6 +841,16 @@ static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
 	return 0;
 }
 
+static const struct soc_device_attribute sdhci_omap_soc_devices[] = {
+	{
+		.machine = "DRA7[45]*",
+		.revision = "ES1.[01]",
+	},
+	{
+		/* sentinel */
+	}
+};
+
 static int sdhci_omap_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -841,6 +862,7 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	struct mmc_host *mmc;
 	const struct of_device_id *match;
 	struct sdhci_omap_data *data;
+	const struct soc_device_attribute *soc;
 
 	match = of_match_device(omap_sdhci_match, dev);
 	if (!match)
@@ -875,6 +897,17 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_pltfm_free;
 
+	soc = soc_device_match(sdhci_omap_soc_devices);
+	if (soc) {
+		omap_host->version = "rev11";
+		if (!strcmp(dev_name(dev), "4809c000.mmc"))
+			mmc->f_max = 96000000;
+		if (!strcmp(dev_name(dev), "480b4000.mmc"))
+			mmc->f_max = 48000000;
+		if (!strcmp(dev_name(dev), "480ad000.mmc"))
+			mmc->f_max = 48000000;
+	}
+
 	pltfm_host->clk = devm_clk_get(dev, "fck");
 	if (IS_ERR(pltfm_host->clk)) {
 		ret = PTR_ERR(pltfm_host->clk);

From 1d3a2220c2a1ab864caf4a64dee745d287089238 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:13 +0530
Subject: [PATCH 04/28] mmc: sdhci-omap: Invoke sdhci_get_of_property to read
 sdhci dt properties

Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index b3dc7f1466e5..d5c1a9c71f95 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -893,6 +893,7 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	host->ioaddr += offset;
 
 	mmc = host->mmc;
+	sdhci_get_of_property(pdev);
 	ret = mmc_of_parse(mmc);
 	if (ret)
 		goto err_pltfm_free;

From c16bc9a7678a27ece028dcbfea8df2049a65dbec Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:14 +0530
Subject: [PATCH 05/28] mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if
 controller can't support 1.8v

The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci.c | 10 ++++++++++
 include/linux/mmc/host.h |  4 ++++
 2 files changed, 14 insertions(+)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 2ededa7f43df..0f3cdca3e769 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -3672,6 +3672,16 @@ int sdhci_setup_host(struct sdhci_host *host)
 	if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) {
 		host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
 				 SDHCI_SUPPORT_DDR50);
+		/*
+		 * The SDHCI controller in a SoC might support HS200/HS400
+		 * (indicated using mmc-hs200-1_8v/mmc-hs400-1_8v dt property),
+		 * but if the board is modeled such that the IO lines are not
+		 * connected to 1.8v then HS200/HS400 cannot be supported.
+		 * Disable HS200/HS400 if the board does not have 1.8v connected
+		 * to the IO lines. (Applicable for other modes in 1.8v)
+		 */
+		mmc->caps2 &= ~(MMC_CAP2_HSX00_1_8V | MMC_CAP2_HS400_ES);
+		mmc->caps &= ~(MMC_CAP_1_8V_DDR | MMC_CAP_UHS);
 	}
 
 	/* Any UHS-I mode in caps implies SDR12 and SDR25 support. */
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 85146235231e..4e80c199c9c2 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -320,6 +320,9 @@ struct mmc_host {
 #define MMC_CAP_UHS_SDR50	(1 << 18)	/* Host supports UHS SDR50 mode */
 #define MMC_CAP_UHS_SDR104	(1 << 19)	/* Host supports UHS SDR104 mode */
 #define MMC_CAP_UHS_DDR50	(1 << 20)	/* Host supports UHS DDR50 mode */
+#define MMC_CAP_UHS		(MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | \
+				 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | \
+				 MMC_CAP_UHS_DDR50)
 /* (1 << 21) is free for reuse */
 #define MMC_CAP_DRIVER_TYPE_A	(1 << 23)	/* Host supports Driver Type A */
 #define MMC_CAP_DRIVER_TYPE_C	(1 << 24)	/* Host supports Driver Type C */
@@ -345,6 +348,7 @@ struct mmc_host {
 #define MMC_CAP2_HS400_1_2V	(1 << 16)	/* Can support HS400 1.2V */
 #define MMC_CAP2_HS400		(MMC_CAP2_HS400_1_8V | \
 				 MMC_CAP2_HS400_1_2V)
+#define MMC_CAP2_HSX00_1_8V	(MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)
 #define MMC_CAP2_HSX00_1_2V	(MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
 #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
 #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18)	/* No physical write protect pin, assume that card is always read-write */

From a999fd9392310ff44b684f2011a60de7c7e73891 Mon Sep 17 00:00:00 2001
From: Adrian Hunter <adrian.hunter@intel.com>
Date: Fri, 27 Apr 2018 17:17:15 +0530
Subject: [PATCH 06/28] mmc: sdhci: Add quirk to disable HW timeout

Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.

Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.

Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci.c | 38 ++++++++++++++++++++++++++++++++++----
 drivers/mmc/host/sdhci.h |  5 +++++
 2 files changed, 39 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 0f3cdca3e769..8da118d0d2c4 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -709,12 +709,15 @@ static u32 sdhci_sdma_address(struct sdhci_host *host)
 		return sg_dma_address(host->data->sg);
 }
 
-static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
+static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
+			     bool *too_big)
 {
 	u8 count;
 	struct mmc_data *data = cmd->data;
 	unsigned target_timeout, current_timeout;
 
+	*too_big = true;
+
 	/*
 	 * If the host controller provides us with an incorrect timeout
 	 * value, just skip the check and use 0xE.  The hardware may take
@@ -768,9 +771,12 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 	}
 
 	if (count >= 0xF) {
-		DBG("Too large timeout 0x%x requested for CMD%d!\n",
-		    count, cmd->opcode);
+		if (!(host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT))
+			DBG("Too large timeout 0x%x requested for CMD%d!\n",
+			    count, cmd->opcode);
 		count = 0xE;
+	} else {
+		*too_big = false;
 	}
 
 	return count;
@@ -790,6 +796,16 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 }
 
+static void sdhci_set_data_timeout_irq(struct sdhci_host *host, bool enable)
+{
+	if (enable)
+		host->ier |= SDHCI_INT_DATA_TIMEOUT;
+	else
+		host->ier &= ~SDHCI_INT_DATA_TIMEOUT;
+	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
+	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
+}
+
 static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 {
 	u8 count;
@@ -797,7 +813,17 @@ static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 	if (host->ops->set_timeout) {
 		host->ops->set_timeout(host, cmd);
 	} else {
-		count = sdhci_calc_timeout(host, cmd);
+		bool too_big = false;
+
+		count = sdhci_calc_timeout(host, cmd, &too_big);
+
+		if (too_big &&
+		    host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT) {
+			sdhci_set_data_timeout_irq(host, false);
+		} else if (!(host->ier & SDHCI_INT_DATA_TIMEOUT)) {
+			sdhci_set_data_timeout_irq(host, true);
+		}
+
 		sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
 	}
 }
@@ -3616,6 +3642,10 @@ int sdhci_setup_host(struct sdhci_host *host)
 		mmc->max_busy_timeout /= host->timeout_clk;
 	}
 
+	if (host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT &&
+	    !host->ops->get_max_timeout_count)
+		mmc->max_busy_timeout = 0;
+
 	mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
 	mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
 
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index c95b0a4a7594..f6555c0f4ad3 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -437,6 +437,11 @@ struct sdhci_host {
 #define SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN		(1<<15)
 /* Controller has CRC in 136 bit Command Response */
 #define SDHCI_QUIRK2_RSP_136_HAS_CRC			(1<<16)
+/*
+ * Disable HW timeout if the requested timeout is more than the maximum
+ * obtainable timeout.
+ */
+#define SDHCI_QUIRK2_DISABLE_HW_TIMEOUT			(1<<17)
 
 	int irq;		/* Device IRQ */
 	void __iomem *ioaddr;	/* Mapped address */

From 0bb28d738fb2066b314d0fe2eccffd1cab59517b Mon Sep 17 00:00:00 2001
From: Adrian Hunter <adrian.hunter@intel.com>
Date: Fri, 27 Apr 2018 17:17:16 +0530
Subject: [PATCH 07/28] mmc: sdhci: Factor out target_timeout calculation

Factor out the target_timeout calculation so it can be re-used.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci.c | 48 +++++++++++++++++++++++++---------------
 1 file changed, 30 insertions(+), 18 deletions(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 8da118d0d2c4..b229354e5b88 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -709,6 +709,35 @@ static u32 sdhci_sdma_address(struct sdhci_host *host)
 		return sg_dma_address(host->data->sg);
 }
 
+static unsigned int sdhci_target_timeout(struct sdhci_host *host,
+					 struct mmc_command *cmd,
+					 struct mmc_data *data)
+{
+	unsigned int target_timeout;
+
+	/* timeout in us */
+	if (!data) {
+		target_timeout = cmd->busy_timeout * 1000;
+	} else {
+		target_timeout = DIV_ROUND_UP(data->timeout_ns, 1000);
+		if (host->clock && data->timeout_clks) {
+			unsigned long long val;
+
+			/*
+			 * data->timeout_clks is in units of clock cycles.
+			 * host->clock is in Hz.  target_timeout is in us.
+			 * Hence, us = 1000000 * cycles / Hz.  Round up.
+			 */
+			val = 1000000ULL * data->timeout_clks;
+			if (do_div(val, host->clock))
+				target_timeout++;
+			target_timeout += val;
+		}
+	}
+
+	return target_timeout;
+}
+
 static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
 			     bool *too_big)
 {
@@ -732,24 +761,7 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
 		return 0xE;
 
 	/* timeout in us */
-	if (!data)
-		target_timeout = cmd->busy_timeout * 1000;
-	else {
-		target_timeout = DIV_ROUND_UP(data->timeout_ns, 1000);
-		if (host->clock && data->timeout_clks) {
-			unsigned long long val;
-
-			/*
-			 * data->timeout_clks is in units of clock cycles.
-			 * host->clock is in Hz.  target_timeout is in us.
-			 * Hence, us = 1000000 * cycles / Hz.  Round up.
-			 */
-			val = 1000000ULL * data->timeout_clks;
-			if (do_div(val, host->clock))
-				target_timeout++;
-			target_timeout += val;
-		}
-	}
+	target_timeout = sdhci_target_timeout(host, cmd, data);
 
 	/*
 	 * Figure out needed cycles.

From fc1fa1b7db27546803905feef403cedf40ca027a Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:17 +0530
Subject: [PATCH 08/28] mmc: sdhci: Program a relatively accurate SW timeout
 value

sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci.c | 52 ++++++++++++++++++++++++++++++++++------
 drivers/mmc/host/sdhci.h | 10 ++++++++
 2 files changed, 55 insertions(+), 7 deletions(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index b229354e5b88..1c828e0e9905 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -738,6 +738,39 @@ static unsigned int sdhci_target_timeout(struct sdhci_host *host,
 	return target_timeout;
 }
 
+static void sdhci_calc_sw_timeout(struct sdhci_host *host,
+				  struct mmc_command *cmd)
+{
+	struct mmc_data *data = cmd->data;
+	struct mmc_host *mmc = host->mmc;
+	struct mmc_ios *ios = &mmc->ios;
+	unsigned char bus_width = 1 << ios->bus_width;
+	unsigned int blksz;
+	unsigned int freq;
+	u64 target_timeout;
+	u64 transfer_time;
+
+	target_timeout = sdhci_target_timeout(host, cmd, data);
+	target_timeout *= NSEC_PER_USEC;
+
+	if (data) {
+		blksz = data->blksz;
+		freq = host->mmc->actual_clock ? : host->clock;
+		transfer_time = (u64)blksz * NSEC_PER_SEC * (8 / bus_width);
+		do_div(transfer_time, freq);
+		/* multiply by '2' to account for any unknowns */
+		transfer_time = transfer_time * 2;
+		/* calculate timeout for the entire data */
+		host->data_timeout = data->blocks * target_timeout +
+				     transfer_time;
+	} else {
+		host->data_timeout = target_timeout;
+	}
+
+	if (host->data_timeout)
+		host->data_timeout += MMC_CMD_TRANSFER_TIME;
+}
+
 static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
 			     bool *too_big)
 {
@@ -831,6 +864,7 @@ static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 
 		if (too_big &&
 		    host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT) {
+			sdhci_calc_sw_timeout(host, cmd);
 			sdhci_set_data_timeout_irq(host, false);
 		} else if (!(host->ier & SDHCI_INT_DATA_TIMEOUT)) {
 			sdhci_set_data_timeout_irq(host, true);
@@ -845,6 +879,8 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
 	u8 ctrl;
 	struct mmc_data *data = cmd->data;
 
+	host->data_timeout = 0;
+
 	if (sdhci_data_line_cmd(cmd))
 		sdhci_set_timeout(host, cmd);
 
@@ -1198,13 +1234,6 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 		mdelay(1);
 	}
 
-	timeout = jiffies;
-	if (!cmd->data && cmd->busy_timeout > 9000)
-		timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
-	else
-		timeout += 10 * HZ;
-	sdhci_mod_timer(host, cmd->mrq, timeout);
-
 	host->cmd = cmd;
 	if (sdhci_data_line_cmd(cmd)) {
 		WARN_ON(host->data_cmd);
@@ -1244,6 +1273,15 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 	    cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200)
 		flags |= SDHCI_CMD_DATA;
 
+	timeout = jiffies;
+	if (host->data_timeout)
+		timeout += nsecs_to_jiffies(host->data_timeout);
+	else if (!cmd->data && cmd->busy_timeout > 9000)
+		timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
+	else
+		timeout += 10 * HZ;
+	sdhci_mod_timer(host, cmd->mrq, timeout);
+
 	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
 }
 EXPORT_SYMBOL_GPL(sdhci_send_command);
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index f6555c0f4ad3..23966f887da6 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -332,6 +332,14 @@ struct sdhci_adma2_64_desc {
 /* Allow for a a command request and a data request at the same time */
 #define SDHCI_MAX_MRQS		2
 
+/*
+ * 48bit command and 136 bit response in 100KHz clock could take upto 2.48ms.
+ * However since the start time of the command, the time between
+ * command and response, and the time between response and start of data is
+ * not known, set the command transfer time to 10ms.
+ */
+#define MMC_CMD_TRANSFER_TIME	(10 * NSEC_PER_MSEC) /* max 10 ms */
+
 enum sdhci_cookie {
 	COOKIE_UNMAPPED,
 	COOKIE_PRE_MAPPED,	/* mapped by sdhci_pre_req() */
@@ -555,6 +563,8 @@ struct sdhci_host {
 	/* Host SDMA buffer boundary. */
 	u32			sdma_boundary;
 
+	u64			data_timeout;
+
 	unsigned long private[0] ____cacheline_aligned;
 };
 

From 25f80d86059c4b78eeec8cb42db158ad2a29eb02 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:18 +0530
Subject: [PATCH 09/28] mmc: sdhci-omap: Workaround for Errata i834
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.

The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index d5c1a9c71f95..2232a9974b21 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -715,7 +715,8 @@ static const struct sdhci_pltfm_data sdhci_omap_pdata = {
 		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC,
 	.quirks2 = SDHCI_QUIRK2_ACMD23_BROKEN |
 		   SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
-		   SDHCI_QUIRK2_RSP_136_HAS_CRC,
+		   SDHCI_QUIRK2_RSP_136_HAS_CRC |
+		   SDHCI_QUIRK2_DISABLE_HW_TIMEOUT,
 	.ops = &sdhci_omap_ops,
 };
 

From 3031ec961d0d5d9502b56c86e9cbdc680012d7cc Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:19 +0530
Subject: [PATCH 10/28] dt-bindings: sdhci-omap: Add K2G specific binding

Add binding for the TI's sdhci-omap controller present in K2G.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 Documentation/devicetree/bindings/mmc/sdhci-omap.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
index 51775a372c06..8d09b837e350 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
@@ -4,7 +4,9 @@ Refer to mmc.txt for standard MMC bindings.
 
 Required properties:
 - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers
+	      Should be "ti,k2g-sdhci" for K2G
 - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1
+	     (Not required for K2G).
 
 Example:
 	mmc1: mmc@4809c000 {

From 6d75df75abb15109d6305f5cb22793752b3b7ab8 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:20 +0530
Subject: [PATCH 11/28] mmc: sdhci-omap: Add support for MMC/SD controller in
 k2g SoC

Add support for the new compatible added specifically to support
k2g's MMC/SD controller.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index 2232a9974b21..b11c846dd8a1 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -720,6 +720,10 @@ static const struct sdhci_pltfm_data sdhci_omap_pdata = {
 	.ops = &sdhci_omap_ops,
 };
 
+static const struct sdhci_omap_data k2g_data = {
+	.offset = 0x200,
+};
+
 static const struct sdhci_omap_data dra7_data = {
 	.offset = 0x200,
 	.flags	= SDHCI_OMAP_REQUIRE_IODELAY,
@@ -727,6 +731,7 @@ static const struct sdhci_omap_data dra7_data = {
 
 static const struct of_device_id omap_sdhci_match[] = {
 	{ .compatible = "ti,dra7-sdhci", .data = &dra7_data },
+	{ .compatible = "ti,k2g-sdhci", .data = &k2g_data },
 	{},
 };
 MODULE_DEVICE_TABLE(of, omap_sdhci_match);

From efde12b246d7704a5697cdaea4512fd97030bb36 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:21 +0530
Subject: [PATCH 12/28] mmc: sdhci-omap: Add sdhci_omap specific ops for
 enable_sdio_irq

Add sdhci_omap_enable_sdio_irq to set CTPL and CLKEXTFREE bits in
MMCHS_CON register required to detect asynchronous card interrupt
on DAT[1].

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index b11c846dd8a1..bd5e03d177e0 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -36,6 +36,7 @@
 #define CON_DDR			BIT(19)
 #define CON_CLKEXTFREE		BIT(16)
 #define CON_PADEN		BIT(15)
+#define CON_CTPL		BIT(11)
 #define CON_INIT		BIT(1)
 #define CON_OD			BIT(0)
 
@@ -226,6 +227,23 @@ static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host,
 	}
 }
 
+static void sdhci_omap_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
+	u32 reg;
+
+	reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+	if (enable)
+		reg |= (CON_CTPL | CON_CLKEXTFREE);
+	else
+		reg &= ~(CON_CTPL | CON_CLKEXTFREE);
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+
+	sdhci_enable_sdio_irq(mmc, enable);
+}
+
 static inline void sdhci_omap_set_dll(struct sdhci_omap_host *omap_host,
 				      int count)
 {
@@ -962,6 +980,7 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	host->mmc_host_ops.set_ios = sdhci_omap_set_ios;
 	host->mmc_host_ops.card_busy = sdhci_omap_card_busy;
 	host->mmc_host_ops.execute_tuning = sdhci_omap_execute_tuning;
+	host->mmc_host_ops.enable_sdio_irq = sdhci_omap_enable_sdio_irq;
 
 	ret = sdhci_setup_host(host);
 	if (ret)

From 75b732d570ac7a6bd53fa770adcb64f9afabcdda Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:22 +0530
Subject: [PATCH 13/28] dt-bindings: sdhci-omap: Add pinctrl bindings

Add pinctrl binding rquired to get the mux mode and IODelay
values from devicetree.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 Documentation/devicetree/bindings/mmc/sdhci-omap.txt | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
index 8d09b837e350..393848c2138e 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
@@ -7,6 +7,11 @@ Required properties:
 	      Should be "ti,k2g-sdhci" for K2G
 - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1
 	     (Not required for K2G).
+- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50",
+		 "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104",
+		 "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11",
+		 "hs200_1_8v",
+- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
 
 Example:
 	mmc1: mmc@4809c000 {

From 3f4028780287ff5a7308f40e10bbba9a42b993aa Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:17:23 +0530
Subject: [PATCH 14/28] mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode

commit 8d20b2eae6c47b095523 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/host/sdhci-omap.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index bd5e03d177e0..f3a7c8ece4be 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -842,8 +842,15 @@ static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
 
 	state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_1_8v", caps,
 						 MMC_CAP_1_8V_DDR);
-	if (!IS_ERR(state))
+	if (!IS_ERR(state)) {
 		pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+	} else {
+		state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_3_3v",
+							 caps,
+							 MMC_CAP_3_3V_DDR);
+		if (!IS_ERR(state))
+			pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+	}
 
 	state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs", caps,
 						 MMC_CAP_SD_HIGHSPEED);

From adc0bbb89e84b8b84cdab356c5c96269635b6227 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:38:52 +0530
Subject: [PATCH 15/28] ARM: dts: dra72-evm-common: Remove mmc specific pinmux

mmc specific pinmux is selected from dra72x-mmc-iodelay.dtsi, so remove
it from dra72-evm-common.dtsi.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra72-evm-common.dtsi | 27 -------------------------
 1 file changed, 27 deletions(-)

diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index e85f560a2f78..8e3b185d864b 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -174,33 +174,6 @@
 };
 
 &dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-
 	dcan1_pins_default: dcan1_pins_default {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */

From bcf3c113bac5f925ef93ef2059c09dbbacbb997d Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:38:53 +0530
Subject: [PATCH 16/28] ARM: dts: dra71-evm: Add "vqmmc-supply" property for
 mmc2

Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra71-evm.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts
index ebc4bbae981e..64c57d87ca2f 100644
--- a/arch/arm/boot/dts/dra71-evm.dts
+++ b/arch/arm/boot/dts/dra71-evm.dts
@@ -204,6 +204,7 @@
 	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
 	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
 	vmmc-supply = <&evm_1v8_sw>;
+	vqmmc-supply = <&evm_1v8_sw>;
 };
 
 &mac {

From ca2618b5d5b04a1e2e96244b00b54479cb6cf2b6 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:38:54 +0530
Subject: [PATCH 17/28] ARM: dts: dra7-mmc-iodelay: Add a new pinctrl group for
 clk line without pullup

During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.

According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.

In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.

Add a new pinctrl group for clock line without pullup to be used in boards
where mmc1_clk line is not connected to an external pullup.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra7-mmc-iodelay.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
 create mode 100644 arch/arm/boot/dts/dra7-mmc-iodelay.dtsi

diff --git a/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi
new file mode 100644
index 000000000000..aa0947266526
--- /dev/null
+++ b/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MMC IOdelay values for TI's DRA7xx SoCs.
+ * Copyright (C) 2018 Texas Instruments
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ */
+
+&dra7_pmx_core {
+	mmc1_pins_default_no_clk_pu: mmc1_pins_default_no_clk_pu {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+};

From edfc459c10393f7058812960ea00f396f90e9f8f Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:38:55 +0530
Subject: [PATCH 18/28] ARM: dts: am57xx-idk: Use pinctrl group from
 dra7-mmc-iodelay.dtsi to select pulldown

commit 18aa0f4bca701cb078a6 ("ARM: dts: am57xx-idk: Select pull down
for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in am57xx-idk-common.dtsi in order to change the CLK
line to PIN_INPUT_PULLDOWN. However instead of modifying the pinctrl
group, use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line without
external pull up.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am571x-idk.dts         |  3 ++-
 arch/arm/boot/dts/am572x-idk.dts         |  3 ++-
 arch/arm/boot/dts/am57xx-idk-common.dtsi | 11 -----------
 3 files changed, 4 insertions(+), 13 deletions(-)

diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index a2555140babc..f7de03eb4377 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -10,6 +10,7 @@
 #include "dra72x.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include "dra7-mmc-iodelay.dtsi"
 #include "dra72x-mmc-iodelay.dtsi"
 #include "am57xx-idk-common.dtsi"
 
@@ -102,7 +103,7 @@
 
 &mmc1 {
 	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
-	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
 	pinctrl-1 = <&mmc1_pins_hs>;
 	pinctrl-2 = <&mmc1_pins_sdr12>;
 	pinctrl-3 = <&mmc1_pins_sdr25>;
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index 3a02ed720957..98b42ef33c46 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include "dra74x.dtsi"
+#include "dra7-mmc-iodelay.dtsi"
 #include "dra74x-mmc-iodelay.dtsi"
 #include "am572x-idk-common.dtsi"
 
@@ -20,7 +21,7 @@
 
 &mmc1 {
 	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
-	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
 	pinctrl-1 = <&mmc1_pins_hs>;
 	pinctrl-2 = <&mmc1_pins_sdr12>;
 	pinctrl-3 = <&mmc1_pins_sdr25>;
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi
index 43cdf523a8a0..43a6d0590f7c 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi
@@ -115,17 +115,6 @@
 			DRA7XX_CORE_IOPAD(0x37d4, MUX_MODE15 | PULL_UP)	/* dcan1_rx.off */
 		>;
 	};
-
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
 };
 
 &i2c1 {

From f306c2510ab8cabb1b1f9f3dcd068c82e338a8d6 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:38:56 +0530
Subject: [PATCH 19/28] ARM: dts: dra71-evm: Use pinctrl group from
 dra7-mmc-iodelay.dtsi to select pulldown

commit 0e43884cca77218d2eccc331396e8 ("ARM: dts: dra71-evm: Select pull
down for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in dra71-evm.dts to change the CLK line to
PIN_INPUT_PULLDOWN. However instead of changing the pinctrl group,
use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line
without external pull up.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra71-evm.dts | 16 ++--------------
 1 file changed, 2 insertions(+), 14 deletions(-)

diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts
index 64c57d87ca2f..b7aeaeeead3b 100644
--- a/arch/arm/boot/dts/dra71-evm.dts
+++ b/arch/arm/boot/dts/dra71-evm.dts
@@ -7,6 +7,7 @@
  */
 
 #include "dra72-evm-common.dtsi"
+#include "dra7-mmc-iodelay.dtsi"
 #include "dra72x-mmc-iodelay.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
 
@@ -50,19 +51,6 @@
 	};
 };
 
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-};
-
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -187,7 +175,7 @@
 
 &mmc1 {
 	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
-	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
 	pinctrl-1 = <&mmc1_pins_hs>;
 	pinctrl-2 = <&mmc1_pins_sdr12>;
 	pinctrl-3 = <&mmc1_pins_sdr25>;

From 94aeaa4300daf82158ba194674d223502cfd9300 Mon Sep 17 00:00:00 2001
From: Sekhar Nori <nsekhar@ti.com>
Date: Fri, 27 Apr 2018 17:38:57 +0530
Subject: [PATCH 20/28] ARM: dts: am574x-idk: Add pinmux configuration for MMC

Include dra76x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for am574x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am574x-idk.dts.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am574x-idk.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts
index 41e12a382d2f..c7718b2d9fdf 100644
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/am574x-idk.dts
@@ -7,6 +7,8 @@
 /dts-v1/;
 
 #include "dra76x.dtsi"
+#include "dra7-mmc-iodelay.dtsi"
+#include "dra76x-mmc-iodelay.dtsi"
 #include "am572x-idk-common.dtsi"
 
 / {
@@ -20,3 +22,21 @@
 		spi-max-frequency = <96000000>;
 	};
 };
+
+&mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_default>;
+	pinctrl-3 = <&mmc1_pins_hs>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>;
+	pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>;
+};
+
+&mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_default>;
+	pinctrl-2 = <&mmc2_pins_default>;
+};

From fc7a0397d255c076120734e49062185d2d29fcef Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:38:58 +0530
Subject: [PATCH 21/28] ARM: dts: am57xx-beagle-x15/am57xx-idk: Fix
 pinctrl-names

The IO lines of MMC2 in am57xx-beagle-x15/am57xx-idk is connected to
3.3v. Use "ddr_3_3v" instead of "ddr_1_8v" to indicate DDR mode
works in 3.3v on these boards.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/am571x-idk.dts        | 2 +-
 arch/arm/boot/dts/am572x-idk.dts        | 2 +-
 arch/arm/boot/dts/am574x-idk.dts        | 2 +-
 arch/arm/boot/dts/am57xx-beagle-x15.dts | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index f7de03eb4377..5bb9d68d6e90 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -113,7 +113,7 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-names = "default", "hs", "ddr_3_3v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index 98b42ef33c46..3ef9111d0e8b 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -31,7 +31,7 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-names = "default", "hs", "ddr_3_3v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_rev20>;
diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts
index c7718b2d9fdf..378dfa780ac1 100644
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/am574x-idk.dts
@@ -35,7 +35,7 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-names = "default", "hs", "ddr_3_3v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_default>;
 	pinctrl-2 = <&mmc2_pins_default>;
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index d6689106d2a8..c76ea6579a81 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -28,7 +28,7 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-names = "default", "hs", "ddr_3_3v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;

From 70539a529806f3b7d4b66282347e17599dacd64b Mon Sep 17 00:00:00 2001
From: Hari Nagalla <hnagalla@ti.com>
Date: Fri, 27 Apr 2018 17:38:59 +0530
Subject: [PATCH 22/28] ARM: dts: dra72-evm-common: Add wilink8 wlan support

Wilink8 module is a combo wireless connectivity card based
on Texas Instrument's wl18xx solution.

Add support for the wlan capabilities of this module by muxing
the relevant mmc lines, and setting the required device-tree
data.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
[nsekhar@ti.com: drop WLAN_EN pinmux. It should be done by bootloader.
                 Also, some commit message adjustments]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra72-evm-common.dtsi   | 42 +++++++++++++++++++++++
 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi | 11 ++++++
 2 files changed, 53 insertions(+)

diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index 8e3b185d864b..b81214051a89 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -44,6 +44,16 @@
 		regulator-boot-on;
 	};
 
+	evm_3v6: fixedregulator-evm_3v6 {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v6";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		vin-supply = <&evm_5v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vsys_3v3: fixedregulator-vsys3v3 {
 		/* Output 2 of TPS43351QDAPRQ1 on dra72-evm */
 		/* Output 2 of LM5140QRWGTQ1 on dra71-evm */
@@ -171,6 +181,15 @@
 			clocks = <&atl_clkin2_ck>;
 		};
 	};
+
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &dra7_pmx_core {
@@ -398,6 +417,29 @@
 	max-frequency = <192000000>;
 };
 
+&mmc4 {
+	status = "okay";
+	vmmc-supply = <&evm_3v6>;
+	vqmmc-supply = <&vmmcwl_fixed>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "hs", "sdr12", "sdr25";
+	pinctrl-0 = <&mmc4_pins_default>;
+	pinctrl-1 = <&mmc4_pins_default>;
+	pinctrl-2 = <&mmc4_pins_default>;
+	pinctrl-3 = <&mmc4_pins_default>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wifi@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
 &mac {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
index 088013c6dc6e..edad87c4292c 100644
--- a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
@@ -202,6 +202,17 @@
 			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
 		>;
 	};
+
+	mmc4_pins_default: mmc4_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
+			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
+			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
+			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
+			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
+			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
+		>;
+	};
 };
 
 &dra7_iodelay_core {

From 135eae49c6cc5186145d1d5bcc375ee82ab60d36 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:39:00 +0530
Subject: [PATCH 23/28] ARM: dts: dra7-evm: Model EVM_3V6 regulator

On TI's DRA74x EVM, EVM_3V6 is connected is connected to the VBAT line
of the wilink card. Model it here so that it can be used while adding
wilink8 WLAN support.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra7-evm.dts | 42 ++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index f1425b0f3a54..181289a28ca1 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -20,6 +20,16 @@
 		reg = <0x0 0x80000000 0x0 0x60000000>; /* 1536 MB */
 	};
 
+	evm_12v0: fixedregulator-evm_12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	evm_1v8_sw: fixedregulator-evm_1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "evm_1v8";
@@ -54,6 +64,38 @@
 		regulator-max-microvolt = <1800000>;
 	};
 
+	evm_3v3: fixedregulator-evm3v3 {
+		/* Output of Cntlr A of TPS43351-Q1 on dra7-evm */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm_5v0 {
+		/* Output of Cntlr B of TPS43351-Q1 on dra7-evm */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_3v6: fixedregulator-evm_3v6 {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v6";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		vin-supply = <&evm_5v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	extcon_usb2: extcon_usb2 {
 		compatible = "linux,extcon-usb-gpio";
 		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;

From fdcc50103cd061d06a6ab6ea3c2c4d4c9468792a Mon Sep 17 00:00:00 2001
From: Hari Nagalla <hnagalla@ti.com>
Date: Fri, 27 Apr 2018 17:39:01 +0530
Subject: [PATCH 24/28] ARM: dts: dra7-evm: Add wilink8 wlan support

The wilink module is a combo wireless connectivity sdio
card based on Texas Instrument's wl18xx solution. It is a
4-wire, 1.8V, embedded sdio wlan device with an external
irq line and is power-controlled by a gpio-based fixed
regulator.

Add pinmux configuration and IODelay values for MMC4.
On dra7-evm, MMC4 is used for connecting to wilink module.

IODelay data credits to :  Vishal Mahaveer <vishalm@ti.com>
and Sekhar Nori <nsekhar@ti.com>

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra7-evm-common.dtsi | 15 +++++++++++++++
 arch/arm/boot/dts/dra7-evm.dts         | 25 +++++++++++++++++++++++++
 2 files changed, 40 insertions(+)

diff --git a/arch/arm/boot/dts/dra7-evm-common.dtsi b/arch/arm/boot/dts/dra7-evm-common.dtsi
index 05a7b1a01bc3..33230c8b2951 100644
--- a/arch/arm/boot/dts/dra7-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra7-evm-common.dtsi
@@ -260,3 +260,18 @@
 &pcie1_rc {
 	status = "okay";
 };
+
+&mmc4 {
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	non-removable;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wifi@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+	};
+};
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 181289a28ca1..704947cbef48 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -96,6 +96,16 @@
 		regulator-boot-on;
 	};
 
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 8 0>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
 	extcon_usb2: extcon_usb2 {
 		compatible = "linux,extcon-usb-gpio";
 		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
@@ -376,6 +386,21 @@
 	pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
 };
 
+&mmc4 {
+	status = "okay";
+	vmmc-supply = <&evm_3v6>;
+	vqmmc-supply = <&vmmcwl_fixed>;
+	pinctrl-names = "default-rev11", "default", "hs-rev11", "hs", "sdr12-rev11", "sdr12", "sdr25-rev11", "sdr25";
+	pinctrl-0 = <&mmc4_pins_default &mmc4_iodelay_ds_rev11_conf>;
+	pinctrl-1 = <&mmc4_pins_default &mmc4_iodelay_ds_rev20_conf>;
+	pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
+	pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
+	pinctrl-4 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
+	pinctrl-5 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
+	pinctrl-6 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
+	pinctrl-7 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
+};
+
 &cpu0 {
 	vdd-supply = <&smps123_reg>;
 };

From 01c5d96688b2b9509d0fea5752e716faa86f8559 Mon Sep 17 00:00:00 2001
From: Vishal Mahaveer <vishalm@ti.com>
Date: Fri, 27 Apr 2018 17:39:02 +0530
Subject: [PATCH 25/28] ARM: dts: dra76-evm: Add wilink8 wlan support

Add support for WLAN using wilink8 module. On dra76-evm, MMC4 is
used for connecting to wilink8 module.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra76-evm.dts | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
index 2deb96405d06..ad154c7b0632 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/dra76-evm.dts
@@ -42,6 +42,16 @@
 		regulator-boot-on;
 	};
 
+	vio_3v6: fixedregulator-vio_3v6 {
+		compatible = "regulator-fixed";
+		regulator-name = "vio_3v6";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		vin-supply = <&vsys_5v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vsys_3v3: fixedregulator-vsys3v3 {
 		/* Output of Cntlr A of TPS43351-Q1 on dra76-evm */
 		compatible = "regulator-fixed";
@@ -81,6 +91,16 @@
 		vin-supply = <&smps5_reg>;
 	};
 
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 8 0>;	/* gpio5_8 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
 	vtt_fixed: fixedregulator-vtt {
 		compatible = "regulator-fixed";
 		regulator-name = "vtt_fixed";
@@ -331,6 +351,17 @@
 	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>;
 };
 
+&mmc4 {
+	status = "okay";
+	vmmc-supply = <&vio_3v6>;
+	vqmmc-supply = <&vmmcwl_fixed>;
+	pinctrl-names = "default", "hs", "sdr12", "sdr25";
+	pinctrl-0 = <&mmc4_pins_hs &mmc4_iodelay_default_conf>;
+	pinctrl-1 = <&mmc4_pins_hs &mmc4_iodelay_manual1_conf>;
+	pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_manual1_conf>;
+	pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_manual1_conf>;
+};
+
 /* No RTC on this device */
 &rtc {
 	status = "disabled";

From 940293affa7ed7c0bdb1820ecf7a8f12e901d030 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:39:03 +0530
Subject: [PATCH 26/28] ARM: dts: dra7: Use sdhci-omap programming model

Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 .../boot/dts/am57xx-beagle-x15-common.dtsi    |  4 +--
 arch/arm/boot/dts/am57xx-beagle-x15.dts       |  1 +
 arch/arm/boot/dts/am57xx-idk-common.dtsi      |  3 ++-
 arch/arm/boot/dts/dra7-evm.dts                |  1 +
 arch/arm/boot/dts/dra7.dtsi                   | 27 +++++++------------
 arch/arm/boot/dts/dra72-evm-common.dtsi       |  2 +-
 arch/arm/boot/dts/dra76-evm.dts               |  3 ++-
 7 files changed, 19 insertions(+), 22 deletions(-)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index 6204a266212a..ad953113cefb 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -444,8 +444,8 @@
 	vmmc-supply = <&vdd_3v3>;
 	vqmmc-supply = <&vdd_3v3>;
 	bus-width = <8>;
-	ti,non-removable;
-	cap-mmc-dual-data-rate;
+	non-removable;
+	no-1-8-v;
 };
 
 &sata {
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index c76ea6579a81..70a71c641066 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -25,6 +25,7 @@
 	pinctrl-1 = <&mmc1_pins_hs>;
 
 	vmmc-supply = <&ldo1_reg>;
+	no-1-8-v;
 };
 
 &mmc2 {
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi
index 43a6d0590f7c..ad87f1ae904d 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi
@@ -412,8 +412,9 @@
 	vmmc-supply = <&v3_3d>;
 	vqmmc-supply = <&v3_3d>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 	max-frequency = <96000000>;
+	no-1-8-v;
 };
 
 &dcan1 {
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 704947cbef48..0894593860d6 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -377,6 +377,7 @@
 	vmmc-supply = <&evm_1v8_sw>;
 	vqmmc-supply = <&evm_1v8_sw>;
 	bus-width = <8>;
+	non-removable;
 	pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index f4ddd86f2c77..ae2f8dd46328 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1079,14 +1079,10 @@
 		};
 
 		mmc1: mmc@4809c000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x4809c000 0x400>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc1";
-			ti,dual-volt;
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 61>, <&sdma_xbar 62>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			pbias-supply = <&pbias_mmc_reg>;
 			max-frequency = <192000000>;
@@ -1100,40 +1096,37 @@
 		};
 
 		mmc2: mmc@480b4000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x480b4000 0x400>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc2";
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 47>, <&sdma_xbar 48>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			max-frequency = <192000000>;
+			/* SDR104/DDR50/SDR50 bits in CAPA2 is not supported */
+			sdhci-caps-mask = <0x7 0x0>;
 		};
 
 		mmc3: mmc@480ad000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x480ad000 0x400>;
 			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc3";
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 77>, <&sdma_xbar 78>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			/* Errata i887 limits max-frequency of MMC3 to 64 MHz */
 			max-frequency = <64000000>;
+			/* SDMA is not supported */
+			sdhci-caps-mask = <0x0 0x400000>;
 		};
 
 		mmc4: mmc@480d1000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x480d1000 0x400>;
 			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc4";
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 57>, <&sdma_xbar 58>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			max-frequency = <192000000>;
+			/* SDMA is not supported */
+			sdhci-caps-mask = <0x0 0x400000>;
 		};
 
 		mmu0_dsp1: mmu@40d01000 {
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index b81214051a89..df174f5c15d1 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -413,7 +413,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins_default>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 	max-frequency = <192000000>;
 };
 
diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
index ad154c7b0632..c07f0051844d 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/dra76-evm.dts
@@ -327,7 +327,7 @@
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vio_3v3_sd>;
-	vmmc_aux-supply = <&ldo4_reg>;
+	vqmmc-supply = <&ldo4_reg>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode
@@ -344,6 +344,7 @@
 	vmmc-supply = <&vio_1v8>;
 	vqmmc-supply = <&vio_1v8>;
 	bus-width = <8>;
+	non-removable;
 	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_default>;

From c29fd489118a2abd2d17c49ae980e3c67fa6d004 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:39:04 +0530
Subject: [PATCH 27/28] ARM: dts: dra7: Add high speed modes capability to
 MMC1/MMC2 dt node

While the supported UHS mode can be obtained from CAPA2
register, SD Host Controller Standard Specification
doesn't define bits for MMC's HS200 and DDR mode capability.
Add properties to indicate MMC HS200 and DDR speed mode capability in
dt node.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/dra7.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index ae2f8dd46328..9dcd14edc202 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1086,6 +1086,8 @@
 			status = "disabled";
 			pbias-supply = <&pbias_mmc_reg>;
 			max-frequency = <192000000>;
+			mmc-ddr-1_8v;
+			mmc-ddr-3_3v;
 		};
 
 		hdqw1w: 1w@480b2000 {
@@ -1104,6 +1106,9 @@
 			max-frequency = <192000000>;
 			/* SDR104/DDR50/SDR50 bits in CAPA2 is not supported */
 			sdhci-caps-mask = <0x7 0x0>;
+			mmc-hs200-1_8v;
+			mmc-ddr-1_8v;
+			mmc-ddr-3_3v;
 		};
 
 		mmc3: mmc@480ad000 {

From 24a6f1f65ea567d017c598faf1374ee443f73851 Mon Sep 17 00:00:00 2001
From: Kishon Vijay Abraham I <kishon@ti.com>
Date: Fri, 27 Apr 2018 17:39:05 +0530
Subject: [PATCH 28/28] Documentation: ARM: Add new MMC requirements for
 DRA7/K2G

From 4.18 kernel, all the MMC controller instances in DRA7
are programmed using sdhci based driver (sdhci-omap.c). Document
this new requirement here. Both omap2plus_defconfig and
multi_v7_defconfig has CONFIG_MMC_SDHCI_OMAP enabled.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 Documentation/arm/OMAP/README | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/arm/OMAP/README b/Documentation/arm/OMAP/README
index 75645c45d14a..90c6c57d61e8 100644
--- a/Documentation/arm/OMAP/README
+++ b/Documentation/arm/OMAP/README
@@ -5,3 +5,7 @@ KERNEL		NEW DEPENDENCIES
 v4.3+		Update is needed for custom .config files to make sure
 		CONFIG_REGULATOR_PBIAS is enabled for MMC1 to work
 		properly.
+
+v4.18+		Update is needed for custom .config files to make sure
+		CONFIG_MMC_SDHCI_OMAP is enabled for all MMC instances
+		to work in DRA7 and K2G based boards.