arm-soc: soc-specific pinctrl changes

With this, five platforms are moving to the relatively new pinctrl
 subsystem for their pin management, replacing the older soc specific
 in-kernel interfaces with common code.
 
 There is quite a bit of net addition of code for each platform being
 added to the pinctrl subsystem. but the payback comes later when adding
 new boards can be done by only providing new device trees instead.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuw1/AAoJEIwa5zzehBx3wbsP/RFCYzMVyz85BNLQuRyY9eO2
 GCRWd0Vvy3fIfypiPdHdhkq6nIU/JnxgsfBbKX9FvWqvxXi96Ojh13KSIhSI1rQ9
 t14VyuwUXaS3leeCyKxhNF1vRscz2iyEGXJqp+XEN4ckf2nrQCpKBiY5Eg9sH6/J
 fvYgSBY9Lf9nFAn+/wqSKIfdvw7H0NXwUdsLvNU0uCwvrSG929bTxx2AnHX00TdJ
 qf4XLhmatMg1uwdUgL/99ZxxgHlj6o55u7S6aRhUWXNXCimV6uEZ1F35ET37b+x3
 YUltBCIaXjFR7iwNHmkkl42d8uyfkBznB555sY5qS3G/uF5Ma1R5I7fv8EIEy+2w
 bVHsva4lj1yFazic6m8yKTET4i8n6OPiKVNqGnDsp2yb6WzOGSliKdr0Jlo1oNG2
 gS69LcDZxCkXrqEq0Ht8uUoCo9TWei+qhJ6ZOJ1Z3+9ZyFq1iRTKgPVxyA5VaHaB
 wwBbqKrohAwuExY8/gkAj6SYqBOF3l/J8QSB2JjXyj4trLC5UMq+l3L4cIWyMRPc
 fil83hV6460CiIBoKcsnV9hDUS0oh74mv52zHo0Xj73qABqZ4dcrpHVayWjtMtpl
 Z+tUpvD1rMQ+E0gdXDrwMrwILVyCDsBvpFKF4avnujDJ4WmyywtKZ+xvnpMd73VZ
 YrI/+XQsMT8ZfVkkj54D
 =HIfz
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm soc-specific pinctrl changes from Olof Johansson:
 "With this, five platforms are moving to the relatively new pinctrl
  subsystem for their pin management, replacing the older soc specific
  in-kernel interfaces with common code.

  There is quite a bit of net addition of code for each platform being
  added to the pinctrl subsystem.  But the payback comes later when
  adding new boards can be done by only providing new device trees
  instead."

Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}

* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  mtd: nand: gpmi: fix compile error caused by pinctrl call
  ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
  ARM: nomadik: enable PINCTRL_NOMADIK where needed
  ARM: mxs: enable pinctrl support
  video: mxsfb: adopt pinctrl support
  ASoC: mxs-saif: adopt pinctrl support
  i2c: mxs: adopt pinctrl support
  mtd: nand: gpmi: adopt pinctrl support
  mmc: mxs-mmc: adopt pinctrl support
  serial: mxs-auart: adopt pinctrl support
  serial: amba-pl011: adopt pinctrl support
  spi/imx: adopt pinctrl support
  i2c: imx: adopt pinctrl support
  can: flexcan: adopt pinctrl support
  net: fec: adopt pinctrl support
  ARM: ux500: switch MSP to using pinctrl for pins
  ARM: ux500: alter MSP registration to return a device pointer
  ARM: ux500: switch to using pinctrl for uart0
  ARM: ux500: delete custom pin control system
  ARM: ux500: switch over to Nomadik pinctrl driver
  ...

include/linux/pinctrl/pinctrl-state.h

@@ -2,5 +2,18 @@
  * Standard pin control state definitions
  */
 
+/**
+ * @PINCTRL_STATE_DEFAULT: the state the pinctrl handle shall be put
+ *	into as default, usually this means the pins are up and ready to
+ *	be used by the device driver. This state is commonly used by
+ *	hogs to configure muxing and pins at boot.
+ * @PINCTRL_STATE_IDLE: the state the pinctrl handle shall be put into
+ *	when the pins are idle. Could typically be set from a
+ *	pm_runtime_suspend() operation.
+ * @PINCTRL_STATE_SLEEP: the state the pinctrl handle shall be put into
+ *	when the pins are sleeping. Could typically be set from a
+ *	common suspend() function.
+ */
 #define PINCTRL_STATE_DEFAULT "default"
 #define PINCTRL_STATE_IDLE "idle"
+#define PINCTRL_STATE_SLEEP "sleep"

include/linux/platform_data/tegra_usb.h

@@ -26,6 +26,7 @@ struct tegra_ehci_platform_data {
 	/* power down the phy on bus suspend */
 	int power_down_on_bus_suspend;
 	void *phy_config;
+	int vbus_gpio;
 };
 
 #endif /* _TEGRA_USB_H_ */